Symmetry Voyager Assembly Instructions Manual Download | Manualshive

Page: 5 / 17

background image

To report any issues with this product, please contact our customer service department at (888) 552-5699.

For more information, visit www.symmetryoffice.com

VOYAGER 2-LEG ASSEMBLY INSTRUCTIONS

STEPS

2

5

For each top support:

1. Feed the motor cables through the motor housing.
2. Center the motor housing in the top support, ensuring that the mounting holes in the

motor housing and the column remain aligned.

3. Fasten the three parts together using the T40 Torx L-key and the M8 × 1.25 12 mm

screws (4 per column).

«
...
3
4
5
6
7
...
»

Summary of Contents for Voyager


















Reviews:

No comments

Related manuals for Voyager

Brand: LAZBOY Pages: 6

Brand: Yomei Pages: 32

Brand: Yomei Pages: 15

Brand: Balmani Pages: 4

Brand: Happy Babies Pages: 7

Brand: Safco Pages: 7

Brand: Naos Pages: 4

N-GEN CITUS Series

Brand: Neo Chair Pages: 8

Brand: Yaasa Pages: 200

Brand: Canyon Pages: 36

Brand: The Land of Nod Pages: 7

Brand: MAC TOOLS Pages: 6

Brand: Songmics Pages: 16

Brand: SereneLife Pages: 10

TY Pennington Style Mayfield 4 PC

Brand: Sears Pages: 11

Brand: Homelegance Pages: 3

Safco Apprentice II 6689

Brand: LDI Pages: 2

Stilford JBSHBB15WW

Brand: J.Burrows Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands