Symmetry Voyager Assembly Instructions Manual Download | Manualshive

Page: 6 / 17

background image

To report any issues with this product, please contact our customer service department at (888) 552-5699.

For more information, visit www.symmetryoffice.com

VOYAGER 2-LEG ASSEMBLY INSTRUCTIONS

STEPS

3

6

1. Attach the feet to the columns using the 6 mm hex L-key and the M10 × 1.5 30 mm

screws (2 per column).

«
...
4
5
6
7
8
...
»

Summary of Contents for Voyager


















Reviews:

No comments

Related manuals for Voyager

Brand: Gami Pages: 4

Brand: Safco Pages: 2

Brand: VAS Pages: 19

San Fran 2 Person Run Workstation

Brand: Jason.L Pages: 4

Brand: LAZBOY Pages: 10

Brand: LAZBOY Pages: 10

Horizon Quadro A 2P Run workstation 1200x800 mm

Brand: Jason.L Pages: 8

TY Pennington Style Mayfield 4 PC

Brand: Sears Pages: 11

Brand: Bouclair Pages: 2

HANNOVER NON-STORAGE BEDFRAME

Brand: GFW Pages: 12

Citterio 39148XX1

Brand: Axor Pages: 1

Brand: modway Pages: 2

Brand: Prepac Pages: 2

ELINE SB 19027-S5VP

Brand: emob Pages: 6

Brand: TOPSKY Pages: 2

BH17-084-098-50

Brand: Better Homes and Gardens Pages: 16

Brand: hanit Pages: 2

Whitehaven Console Unit QN077

Brand: J D Williams Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands