Symmetry Voyager Assembly Instructions Manual Download | Manualshive

Page: 7 / 17

background image

To report any issues with this product, please contact our customer service department at (888) 552-5699.

For more information, visit www.symmetryoffice.com

VOYAGER 2-LEG ASSEMBLY INSTRUCTIONS

STEPS

4

7

1. Attach the motor housing to the underside of the table top using a #2 Phillips-head

screwdriver or bit and #10 × ¾" screws (2 per motor housing).

Screws belong inside

the motor housing.

«
...
5
6
7
8
9
...
»

Summary of Contents for Voyager


















Reviews:

No comments

Related manuals for Voyager

Brand: Walker Edison Pages: 11

Brand: Officient Pages: 2

Brand: Naterial Pages: 36

Brand: Samson Pages: 8

Japanese Myojin Style Torii Gate

Brand: SAMSGAZEBOS Pages: 7

Brand: TDK Pages: 2

Brand: TDC USA Pages: 9

Brand: Garden Treasures Pages: 9

Brand: yesst Pages: 5

Brand: OLG Pages: 6

Brand: Northridge Home Pages: 9

OSBOURNE 383598

Brand: Next Pages: 9

Brand: BullFrog Pages: 3

Brand: Instant Desks Pages: 2

Surround Light SLVT710

Brand: Zadro Pages: 2

Abeyance EEI -1182

Brand: modway Pages: 4

Brand: Garden Treasures Pages: 5

Brand: Garden Treasures Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands