background image

 

614-00051  Rev 00 

 Attero Tech LLC 2018 

 LIMITED FIVE YEAR WARRANTY 

 
The equipment is warranted for five years from date of purchase from Attero Tech, LLC against defects in materials or workmanship. This 
warranty does not cover equipment which has been abused or damaged by careless handling or shipping. This warranty does not apply to 
used or demonstrator equipment. Should any defect develop, Attero Tech, LLC will, at our option, repair or replace any defective parts without 
charge for either parts or labor. If Attero Tech, LLC cannot correct the defect in the equipment, it will be replaced at no charge with a similar 
new item. Attero Tech, LLC will pay for the cost of returning your equipment to you. This warranty applies only to items returned to Attero 
Tech, LLC, shipping costs prepaid, within five years from the date of purchase. This Limited Warranty is governed by the laws of the State of 
Indiana. It states the entire liability of Attero Tech, LLC and the entire remedy of the purchaser for any breach of warranty as outlined above. 
NEITHER ATTERO TECH, LLC NOR ANYONE INVOLVED IN THE PRODUCTION OR DELIVERY OF THE EQUIPMENT SHALL BE LIABLE FOR ANY 
INDIRECT, SPECIAL, PUNITIVE, CONSEQUENTIAL, OR INCIDENTAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THIS EQUIPMENT 
EVEN IF ATTERO TECH, LLC HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT SHALL THE LIABILITY OF ATTERO TECH, 
LLC EXCEED THE PURCHASE PRICE OF ANY DEFECTIVE EQUIPMENT. 
 
This warranty gives you specific legal rights. You may have additional legal rights which vary from state to state. 
 

Note: This equipment has been tested and found to comply with the limits for a Class A 

digital device, pursuant to Part 15 of the FCC Rules and EN55022. These limits are 

designed to provide reasonable protection against harmful interference when the 

equipment is operated in a commercial environment. This equipment generates, uses, 

and can radiate radio frequency energy and, if not installed and used in accordance with 

the instruction manual, may cause harmful interference to radio communications. 

Operation of this equipment in a residential area is likely to cause harmful interference, 

in which case the user will be required to correct the interference at their own expense. 

 

 
 

 
This symbol means the product must not be discarded as household waste, and should be delivered to an appropriate collection 
facility for recycling. Proper disposal and recycling helps protect natural resources, human health and the environment. For more 
information on disposal and recycling of this product, contact your local municipality, disposal service, or the business where you 
bought this product. 

 
 

 

Summary of Contents for D16Mio















Reviews: