background image

(C) 2021 Syncronorm GmbH

11

The device requires regular maintenance.

Carry out maintenance in accordance with the maintenance schedule:

- If necessary, update your software version.

- Check, if all external cables are working properly.

 

Important information!

Maintenance must be carried out by qualified personnel only!

CE Conformity

This DMX decoder is microprocessor controlled and uses high frequency (8 MHz quartz). The interface 

has been tested in our EMC lab to comply with EN5022B and IEC65/144. To ensure the best perfor-

mance regarding radiated and conducted emissions, please make sure that shielded data cable is used 

and the shield is connected properly to the GND terminal. Shield must never make contact to any other 

signal lines.

Protecting the environment

For the transport and Protective packaging, environmentally friendly  

materials have been choosen that can be supplied normaly recycling.  

Do not just dispose of these materials with your normal household waste,  

but make sure that they are collected for recycling

This product is subject to the European Waste Electrical and Electronic  

Equipment Directive (WEEE).

FCC Statement

This product has been tested and complies with the specifications for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against 

harmful interference in a residential installation. This equipment generates, uses, and can radiate radio 

frequency energy and, if not installed and used according to the instructions, may cause harmful inter-

ference to radio communications. However, there is no guarantee that interference will not occur in a 

particular installation. If this equipment does cause harmful interference to radio or television reception, 

which is found by turning the equipment off and on, the user is encouraged to try to correct the 

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment or devices

• Connect the equipment to an outlet other than the receiver‘s

• Consult a dealer or an experienced radio/TV technician for assistance

FCC Caution: Any change or modification to the product not expressly approved by SLH could void the 

user’s authority to operate the device.

Maintenance and Cleaning

 MAINTANANCE & DISPOSAL

Summary of Contents for SyncroADC














Reviews: