background image

 

PHYSICAL CHARACTERISTICS 

 

      Size: Less connectors and mounting plate.  
  

3.22” W x 5.21”L x 1.26”H        82mm x 132mm x 32mm 

      Weight:  

 

10 oz 

 (0.28 kg) 

      Housing: 

 

Black Powder-Coated Aluminum 

 
 

ELECTRICAL INTERFACE (Standard)

 

 

      Power/Data:   

 

SwitchCraft EN3P8M - 8 Pin 

      Mating Conn:  

 

SwitchCraft EN3C8F  - 8 Pin 

      GPS Antenna: 

 

TNC Jack (Others optional) 

 

 

ELECTRICAL INTERFACE (XTS)

 

 

      Power/Data:   

 

DB-9M 

      Mating Conn:  

 

DB-9F 

      GPS Antenna: 

 

BNC Jack  

 
 

ELECTRICAL INTERFACE (USB)

 

 

      Power/Data:   

 

USB 

      Mating Conn:  

 

USB 

      1PPS   

 

 

SMA 

      GPS Antenna: 

 

BNC Jack  

 
 

ENVIRONMENTAL CONDITIONS

 

 

      Operating Temp:    w/o Batt 

             -40

o

C to +85

o

      Storage Temp: 

w/o Batt 

             -40

o

C to +85

o

      Operating Temp:    w/Batt 

             -20

o

C to +60

o

      

Storage Temp: 

w/Batt 

             -20

o

C to +60

o

      Relative Humidity:               10% to 90%, non-condensing 

 
 

POWER REQUIREMENTS

 

 

+9 to +30VDC (200 mA max) 

Constant 1.6W max 

Summary of Contents for SynPaQ/E











Reviews: