background image

General information |

1

1

General information

1.1

Warning symbols

Danger

Direct hazard

Failure to comply with this warning will lead
directly to death or to serious injury.

Caution

Hazard with a low risk

Failure to comply with this warning may lead to
moderate injuries.

Warning

Potential hazard

Failure to comply with this warning may lead to
death or serious injury.

Important

Hazard with risk of damage to objects

Failure to comply with this warning will lead to
damage to objects.

Note:

Useful information and instructions

1.1.1

Instruction symbols

Instruction

Instruction with fixed sequence

Carry out this action

1. Carry out this action

3. (if applicable, further actions)

(if applicable, further actions)

2. Carry out this action

2

Important safety information

Planners, plant builders and operators are responsible for the proper assembly and intended use.

Read the operating instructions completely and carefully.

Keep the operating instructions and other valid documents, such as the circuit diagram or motor instructions, with
the fan. They must always be available at the place of use.

Observe and respect local conditions, regulations and laws.

Abide by the system-related conditions and requirements of the system manufacturer or plant constructor.

Safety elements may not be dismantled, circumvented or deactivated.

Only use the fan in a flawless condition.

Provide generally prescribed electrical and mechanical protective devices.

During installation, electrical connection, commissioning, troubleshooting, and maintenance, secure the location and
premises against unauthorised access.

Do not circumvent any safety components or put them out of action.

Before any work on the fan, test absence of voltage.

Even when the motor is stopped, dangerous voltages may be present on terminals.

Keep all the warning signs on the fan complete and in a legible condition.

The device is not to be used by persons (including children) with reduced physical, sensory or mental capabilities, or
lack of experience and knowledge, unless they have been given supervision or instruction.

Do not allow children to play with the device.

2.1

Personnel

The fan may only be used by qualified, instructed and trained personnel. The persons must know the relevant safety di-
rectives in order to recognise and to avoid risks. The individual activities and qualifications can be found in Table 1

Qual-

ifications

, page 2.

| 005

Summary of Contents for 247027























Reviews: