22/69 |
F-B90
Installation 1 – Wet
Using Plaster/Mortar/Concrete Filling
1. Opening surfaces must be even and cleaned off. The flexible wall opening must be reinforced as per the standards for plasterboard
walls. The opening dimensions are based on the nominal dimensions of the damper with added clearance. The opening will have the
dimensions of W1 and H1.
2. Insert the damper as per the “Handling of F-B90” section into the middle of the opening so that the damper blade is in the wall. For
damper widths greater than 600 mm, it is recommended to use a duct support inside the damper during installation to avoid any
damage caused to the damper housing by the weight of the filling.
3. Fill in the area between the wall and the damper with gypsum plaster or mortar or concrete filling (3) while being careful not to
foul the damper’s functional parts, which might keep it from working properly. The best way is to cover the functional parts during
installation. To prevent seepage of the filling material, use of boards is recommended.
First, let the plaster or mortar or concrete filling harden and then perform the next steps.
4. After the filling hardens, remove the duct support from inside the damper.
5. If needed, uncover and clean the damper after installation.
6. Make sure the damper works properly.
Installation Distances
According to the EN 1366-2 standard, the minimum distance from the wall or ceiling to the damper body is 75 mm. For multiple
crossings through a fire-resistant wall, the minimum distance between two damper bodies is 200 mm. This applies for distances
between the damper body and any nearby foreign object crossing the fire-resistant wall. Damper clearances vary according to the
type of mechanism and rotation.
Notes:ve - Vertical (wall)
Product typeA1) - Installation with Ducts or Duct with GrilleA2) - Installation without Duct, only with Grille
Summary of Contents for F-B90
