68/69 |
F-B90
The operator performs regular inspections of the dampers as per established regulations and standards at least once every 12
months. The inspection needs to be performed by an employee who has been specifically trained for this purpose by the
manufacturer. The current fire damper condition determined during the inspection needs to be entered into the “Operating Log” along
with the date of the inspection, the legible name, surname and signature of the employee who performed the inspection. The
Operating Log includes a copy of the employee’s authorization.
Any discrepancies discovered must be entered in the Operating Log along with a proposal for their correction. The Operating Log can
be found in
https://design.systemair.com
Before the first installation, inspection must be performed under the same conditions as those applicable to the above-mentioned 12-
month inspections.
It is necessary to inspect the damper’s internal casing, the thermal fuse link, the sealing, the foaming substance, the damper blade’s
condition and its closure when it rests on a backstop in the closed position. There must be no other objects or dirt from the ventilation
duct inside the damper.
NEVER INSPECT THE DAMPERS WHEN THERE IS AIR FLOWING IN THE DUCT SYSTEM!
Recommended Inspection Steps According to the EN 15 650:
1. Damper identification
2. Date of inspection
3. Check the electrical connection of the activation mechanism (where applicable)
4. Check the damper for cleanliness and clean if necessary
5. Check the blade and sealing condition, corrections enter in log (if necessary)
6. Check for proper closure of the fire damper – for details, see the above sections
7. Check the operating functions of the damper: opening and closing using the control system, physical examination of the damper’s
behavior, correct if necessary and enter in log.
8. Check the operating functions of the end switches in the open and closed positions, correct if necessary and enter in log
9. Check whether the damper is fulfilling its role as part of the regulation system (where needed)
10. Check whether the damper remains in its standard operating position.
11. The damper is usually part of a system. In that case the whole system needs to be checked as described with respect to its
operation and requirements published by the builder of the system.
Supplement
Any deviations from the technical specifications contained in SystemairDESIGN and the terms should be discussed with the
manufacturer. We reserve the right to make any changes to the product without prior notice, provided that such changes do not affect
the quality of the product and the required parameters.
Summary of Contents for F-B90
