NTC - IR2
GB - 6
Configuration menu
Item 4- - Item 5-:
The user desired temperature can be set through buttons F or D.
Temperature increase or decrease starts from the factory-set value
of 22C (72F).
Each time button F or D is pressed, temperature is increased or
decreased by ±0.5 degrees (or ±1F).
In this case the temperature range is between 20 C and 24C (68F
to 76F).
In any case, the user can increase this temperature range by
changing item 4 and 5 values.
Item 4 is the starting temperature and item 5 is the value to be
assigned each time button F or D is pressed.
There follow some examples according to the scale range required
(we suggest changing item 5 ONLY):
Configuration menu – Supplement
Item 5 = 2C (4F)
Minimum temp. = 14C (56F) —> automatically set at 15C (59F)
Maximum temp. = 30C (88F)
Item 5 = 1.5C (3F)
Minimum temp. = 16C (60F)
Maximum temp. = 28C (84F)
Item 5 = 1C (2F)
Minimum temp. = 18C (64F)
Maximum temp. = 26C (80F)
The user can also set the value of item 4 so that no temperature
increase or decrease can change it when button F or D is pressed.
To do so, set the desired fixed temperature value in item 4 and set
0C (0F) in item 5.
Anyway, the desired maximum temperature value is 32C (90F).
9-
Lights groups available
0
1
...
4
5
There is no lights/groups to control: no icons
will be displayed
Just one lights group is available: “1” group icons
will not be illuminated
...
Four lights groups are available: “Lamp” and “4”
groups icons will be illuminated
There is no group, but user can manage the light
[Defaults: “0” Lights control disabled.]
YES: Once the Lights Menu
is selected, the groups icon
will be energized on the lcd
(no icons if just one group is
selected)
“A” and “1” icons are
energized in the light
menu.User can manage
all lights or just one
10-
Louver presence
No
Ye
Some units doesn’t have the louver installed. This item
consents to don’t show the louver icon on the LCD
None
Louver installed (Stepper motor or
Synchronous motor + home position)
[Defaults: “No” No louver presence.]
YES
If the unit has the louver,
this icon will be activated
This icon will show on
the LCD the functioning
of the louver
11-
Unit's remote ID
A
1
2
3
...
7
Unit remote ID ALL
Unit remote ID 1
Unit remote ID 2
Unit remote ID 3
...
Unit remote ID 7
[Defaults: “A” All]
YES
12-
YES
In both Occupied or
Unoccupied mode:
The temperature icon will
be hidden
Light and Blind icons will
appear just if selected
HVAC system
Ye
No
Some application needs to manage just the power
module, without any other system linked
An HVAC system is present
An HVAC system is NOT present
[Default: “Ye”: HVAC system is present]
NTC - IR2
GB - 6
Configuration menu
Item 4- - Item 5-:
The user desired temperature can be set through buttons F or D.
Temperature increase or decrease starts from the factory-set value
of 22C (72F).
Each time button F or D is pressed, temperature is increased or
decreased by ±0.5 degrees (or ±1F).
In this case the temperature range is between 20 C and 24C (68F
to 76F).
In any case, the user can increase this temperature range by
changing item 4 and 5 values.
Item 4 is the starting temperature and item 5 is the value to be
assigned each time button F or D is pressed.
There follow some examples according to the scale range required
(we suggest changing item 5 ONLY):
Configuration menu – Supplement
Item 5 = 2C (4F)
Minimum temp. = 14C (56F) —> automatically set at 15C (59F)
Maximum temp. = 30C (88F)
Item 5 = 1.5C (3F)
Minimum temp. = 16C (60F)
Maximum temp. = 28C (84F)
Item 5 = 1C (2F)
Minimum temp. = 18C (64F)
Maximum temp. = 26C (80F)
The user can also set the value of item 4 so that no temperature
increase or decrease can change it when button F or D is pressed.
To do so, set the desired fixed temperature value in item 4 and set
0C (0F) in item 5.
Anyway, the desired maximum temperature value is 32C (90F).
9-
Lights groups available
0
1
...
4
5
There is no lights/groups to control: no icons
will be displayed
Just one lights group is available: “1” group icons
will not be illuminated
...
Four lights groups are available: “Lamp” and “4”
groups icons will be illuminated
There is no group, but user can manage the light
[Defaults: “0” Lights control disabled.]
YES: Once the Lights Menu
is selected, the groups icon
will be energized on the lcd
(no icons if just one group is
selected)
“A” and “1” icons are
energized in the light
menu.User can manage
all lights or just one
10-
Louver presence
No
Ye
Some units doesn’t have the louver installed. This item
consents to don’t show the louver icon on the LCD
None
Louver installed (Stepper motor or
Synchronous motor + home position)
[Defaults: “No” No louver presence.]
YES
If the unit has the louver,
this icon will be activated
This icon will show on
the LCD the functioning
of the louver
11-
Unit's remote ID
A
1
2
3
...
7
Unit remote ID ALL
Unit remote ID 1
Unit remote ID 2
Unit remote ID 3
...
Unit remote ID 7
[Defaults: “A” All]
YES
12-
YES
In both Occupied or
Unoccupied mode:
The temperature icon will
be hidden
Light and Blind icons will
appear just if selected
HVAC system
Ye
No
Some application needs to manage just the power
module, without any other system linked
An HVAC system is present
An HVAC system is NOT present
[Default: “Ye”: HVAC system is present]
IRC
GB
GB - 7
NTC - IR2
E N G L I S H
Installation tests
Refer to the figure at page 3 (Aspect and display).
Once the unit has been installed and configured, the test must be
carried out.
The scope of this test is to check that installation has been carried
out correctly and the unit operates properly when started for the first
time.
Press button B and C simultaneously for at least 5 seconds to enter
the test mode. “A” appears on the display.
The automatic test or one of the 3 manual tests can now be
selected. Press button D and the following options are cyclically
displayed:
A
1
2
3
A
1...
To confirm the desired test press button B within 60 seconds with
the remote control directed towards the unit. Two acoustic signals
(beep beep) indicate if the message is correctly received by the
unit.
Manual test
Three different tests, indicated by the corresponding number, can
be selected.
Each test will force different system outlets.
During the test, all icons on the display are off and only button C
is active to stop the test at any moment. If the test is not stopped
it lasts about 7 minutes.
TEST1- Cooling mode
To start this test, direct the remote control towards the unit and
press button B when “1” is shown on the display.
The message is sent to the system and two acoustic signals
(beep beep) indicate that the message has been correctly
received.
The scope of this test is to check the cooling operation mode.
The forced unit outlets are:
• Cold water valve
• HIGH fan speed
• Condensate draining pump start-up
TEST2- Heating mode
To start this test, direct the remote control towards the unit and
press button B when “2” is shown on the display. The message is
sent to the system and two acoustic signals (beep beep) indicate
that the message has been correctly received. The scope of this
test is to check the heating operation mode.
The forced unit outlets are:
• Hot water valve
• MEDIUM fan speed (HIGH for units with variable speed motor)
TEST3 – Booster heating
(hot water + electric heaters)
To start this test, direct the remote control towards the unit and
press button B when “2” is shown on the display. The message is
sent to the system and two acoustic signals (beep beep) indicate
that the message has been correctly received. The scope of this
test is to check the heating operation mode with electric heaters on.
The forced unit outlets are:
• Hot water valve
• Electric heaters on
• AUTOmatic fan speed
Automatic test
Throughout the entire test the remote control must always be
directed towards the indoor unit so that the unit can correctly
receive the messages cyclically sent by the remote control.
The scope of this test is to check that messages are correctly sent
and received and the unit operates correctly.
The test can not be started with a non-communicating unit (stand-
alone) or if the unit is not equipped with a outlet air sensor.
During the test, all icons on the display are off and only button C is
active to stop the test at any moment.
If the test is not stopped it lasts about 22 minutes.
During the test, the unit diagnostic is active.
The following table shows which unit outlets are forced and which
operating mode is active:
Variable speed fan
motor
Fixed speed fan motor
Minutes
0 to 1
1 to 2
2 to 3
3 to 6
6 to 11
11 to 13
13 to 20
20 to 21
Cooling
(X) / (*)
(X) / (*)
(X) / (*)
X/ *
X/ *
Heating
X/ *
X/ *
Electric
heaters
X/ *
Condensate
draining pump
X/ *
X/ *
X/ *
X/ *
LOW
X
X
MEDIUM
X
HIGH
X
X
HIGH
*
*
*
AUTO
X
X
X
X
AUTO
*
*
*
*
*
X/* = Do not forget that the water valves need a few minutes to open completely. It is only after this time that the cooling or heating effect is felt.
IRC
GB
Summary of Contents for IRC
