background image

89676 02-03-2011 

 

Page 1 of 17  

 

FITTING INSTRUCTIONS 

Product: 

ELECTRIC WINCH 

 

9000lb        9500lb        12000lb 

 

 

For further information contact T.J.M. Head Office on (07) 3865 9999. Distributors Australia wide. 

 

VEHICLE RECOVERY 

ELECTRIC WINCH 

 

 

 
 
 
 
 
 
 
 
 

 

Warranty 

 

1. If any product or part of a product manufactured by TJM is found to be defective during a period of two (2) years after the date of 
purchase, TJM shall repair or replace (at TJM's discretion) the defective product or part. 
 
2. Any defect in a product distributed by TJM, but not manufactured by TJM, shall be dealt with in accordance with, and to the extent 
of, the warranty offered by the manufacturer of that product. 
 
3. TJM does not warrant that the products manufactured by it comply with the laws of the place where those products are purchased 
or  used.  It  is  the  sole  responsibility  of  the  Purchaser  to  ascertain  whether  products  being  purchased  -  or  the  affixation  of  those 
products to any other object - comply with local laws. 
 
4.  Except  to  the  extent  described  in  this  warranty,  TJM  shall  not  be  liable  for  any  other  claim,  including  those  claims  arising  from 
faulty  design,  the  use  of the  product  on  any  indirect  special  or  consequential  damage  or  injury  to  any     person, company  or  other 
entity.  
 
5. Modification or alteration to any product manufactured by TJM to enable fitment in conjunction with other vehicle accessories or 
modifications (e.g. lift kits) will void any warranty claims.

 

CONTENTS 

 

* Warranty 

 

 

* Warnings    

* Operation   

 

* Specifications 

* Safety Precautions  

* Installation   

* Maintenance 

 

* Parts List 

Summary of Contents for 9000lb


















Reviews: