background image

WARRANTY STATEMENT 

 

Products  sold  by  Tabor  Electronics  Ltd.  are  warranted  to be  free  from  defects  in  workmanship  or  materials. 
Tabor Electronics Ltd. will, at its option, either repair or replace any hardware products which prove to be de-
fective during the warranty period. You are a valued customer. Our mission is to make any necessary repairs 
in a reliable and timely manner.

 

Duration of Warranty

 

The  warranty  period  for  this  Tabor  Electronics  Ltd.  hardware  is  three  years,  except  software  and  firmware 
products  designed  for  use  with  Tabor  Electronics  Ltd.  Hardware  is  warranted  not  to  fail  to  execute  its  pro-
gramming instructions due to defect in materials or workmanship for a period of ninety (90) days from the date 
of delivery to the initial end user.

 

Return of Product

 

Authorization  is  required  from  Tabor  Electronics  before  you  send  us  your  product  for  service  or  calibration. 
Call your nearest Tabor Electronics support facility. A list is located on the last page of this manual. If you are 
unsure where to call, contact Tabor Electronics Ltd. Tel Hanan, Israel at 972-4-821-3393 or via fax at 972-4-
821-3388. We can be reached at: support@tabor.co.il

 

Limitation of Warranty

 

Tabor Electronics Ltd. shall be released from all obligations under this warranty in the event repairs or modifi-
cations are made by persons other than authorized Tabor Electronics service personnel or without the written 
consent of Tabor Electronics.  

Tabor  Electronics  Ltd.  expressly  disclaims  any  liability  to  its  customers,  dealers  and  representatives  and  to 
users of its product, and to any other person or persons, for special or consequential damages of any kind and 
from  any  cause  whatsoever  arising  out  of  or  in  any  way connected with the manufacture, sale, handling, re-
pair, maintenance, replacement or use of said products. 

Representations and warranties made by any person including dealers and representatives of Tabor Electron-
ics Ltd., which are inconsistent or in conflict with the terms of this warranty (including but not limited to the limi-
tations of the liability of Tabor Electronics Ltd. as set forth above), shall not be binding upon Tabor Electronics 
Ltd. unless reduced to writing and approved by an officer of Tabor Electronics Ltd. 

This  document  may  contain  flaws,  omissions  or  typesetting  errors.    No  warranty  is  granted  nor  liability  as-
sumed in relation thereto. The information contained herein is periodically updated and changes will be incor-
porated  into  subsequent  editions.  If  you  have  encountered  an  error,  please  notify  us  at  sup-
port@taborelec.com. All specifications are subject to change without prior notice. 

Except as stated above, Tabor Electronics Ltd. makes no warranty, express or implied (either in fact or by op-
eration of law), statutory or otherwise; and except to the extent stated above, Tabor Electronics Ltd. shall have 
no liability under any warranty, express or implied (either in fact or by operation of law), statutory or otherwise. 

 

PROPRIETARY NOTICE 

This  document  and  the  technical  data  herein  disclosed,  are  proprietary  to  Tabor  Electronics,  and  shall  not,  without  e x-
press written permission of Tabor Electronics, be used, in whole or in part to solicit quotations from a competitive source 
or used for manufacture by anyone other than Tabor Electronics. The information herein has been developed at private 
expense, and may only be used for operation and maintenance reference purposes or for purposes of engineering eval-
uation and incorporation into technical specifications and other documents, which specify procurement of products from 
Tabor Electronics. 

Summary of Contents for 9260







































Reviews: