2.
Charging the battery
Warning! The power supply for this charger should be protected by a residual current
device (rated at 30ma or less). A residual current device reduces the risk of electric
shock.
1.
2.
Special safety instructions
●
●
●
●
●
●
●
●
Kickback
Kickback may occur when the nose or tip of the blade touches an object, or when the wood
closes in and pinches the saw blade in the cut.
Tip contact in some cases may cause a sudden reverse reaction, kicking the blade up and back
towards the operator.
Pinching the saw blade along the top of the guide bar may push the saw rapidly back towards
the operator.
Either of these reactions may cause you to lose control of the saw which could result in serious
personal injury. Do not rely
exclusively upon the safety devices built into your saw. As a pruner saw user, you should take
several steps to keep your cutting jobs free from accident or injury.
Kickback is the result of tool misuse and/or incorrect operating procedures or conditions and can
be avoided by taking proper precautions as given below:
●
●
●
Assembly
Warning! Ensure the battery is disconnected from the tool before performing any of the
CORDLESS RECIPROCATING SAW
Introduction
To get the most out of your new cordless garden saw, please read through these instructions
before use. We also recommend that you save the instructions in case you need to refer to them
later.
Technical data
Overview
1.Cutting Blade
2.Clamping Jaw
3.Shoe
4.Blade Holder
5.Clamping Jaw Release
6.Safety Switch
7.Variable Speed Trigger
8.Battery Release Tab
9.Battery Charger
Battery:
Operating time (no load):
Stroke lenght:
Max cutting width:
Blade:
No load speed:
Noise, LpA:
Noise, LwA:
Vibration:
Incl. 1 hour charger
10.8 V 1.5 Ah Li-ion
30 min
20 mm
60 mm
152 mm
0-2,500 rpm
79 dB(A), Kpa 3 dB(A)
90 dB(A), Kpa 3 dB(A)
Ah,WB 8.7 m/s2, K 1.5 m/s2
following
operations
The clamping jaw allows branches to be gripped, providing cutting of unsupported branches
easier. When cutting wider branches or timber, the clamping jaw can be removed and the
garden saw can be used as a standard reciprocating saw.
Fitting the Clamping Jaw
The clamping jaw can not be fitted or removed with the blade fitted. If the blade is fitted, first
remove the blade and then follow the steps below.
1.
2.
3.
Note: Ensure the clamp is secured by pulling the clamp away from the body.
Removing the clamping jaw
1.
2.
Cutting blades
Caution! Do not handle blades without gloves as they are sharp and can become hot after
use, potentially causing personal injury.
Fitting a cutting blade
The garden saw can be fitted with standard reciprocating saw blades, therefore can be used to
cut various timbers and plastics. If the clamping jaw is going to be used, ensure it is fitted before
installing the blade.
1.
2.
3.
Removing the cutting blade
1.
3.
Note: It will take 4-5 charging cycles before the battery reaches optimum charge and run time.
Installing and removing the battery
1.
2.
Use
Switching the saw on and off
1.
2.
Cutting branches using the clamping jaw
1.
2.
Cutting without the clamping jaw
When cutting thicker branches or sawing wood or plastic the clamping jaws can be removed to
prevent them getting in the way of the cut.
1.
Maintenance
1.
2.
3.
4.
5.
Note: we will not be responsible for any damage or injuries caused by repair of the garden saw
by an unauthorised person or by mishandling.
Troubleshooting
LED lights do not illuminate on charger
●
●
The battery has a short run time
●
Variable speed trigger is locked
●
●
Saw has cut out during use
●
Sparking visible through the housing air vents
●
Service centre
Note: Please quote the product model number in connection with all inquiries.
The model number is shown on the front of this manual and on the product rating plate.
For:
•
•
•
•
•
•
Declaration of compliance
We hereby declare that
CORDLESS RECIPROCATING SAW 65307 (RES001)
10.8 V
has been manufactured in accordance with the following standards or normative documents:
EN60745-2-11:2010 EN60745-1:2009+A11:2010
in accordance with the provisions of the following directives
2006/42/EC
The Machinery Directive
Kirsten Vibeke Jensen
Product Safety Manager
05.12.2016 - Shenzhen Take tools Co.,Ltd
Environmental information
Manufactured in P.R.C. 6262
Manufactured for: TACKLIFE
DK-6000 Kolding
© 2016 TACKLIFE
All rights reserved. The content of this manual may not be reproduced, either in full or in part, in
any way by electronic or mechanical means, e.g. photocopying or publication, translated or
saved in an information storage and retrieval system without written permission from Tacklife
1
2
3
5
6
7
8
9
- 01 -
