background image

G.

 

Troubleshooting 

I

f the following “actions” cannot troubleshoot your failure, please 

stop using the 

KP120 and contact the seller who you purchased the product from. 

Case 

Cause 

Solution 

The KP120 does not respond 

after  pressing  the  Power 

Switch 

The  circuits  are  cut  off  by 

self-protection  because  of 

their low voltage or overheat. 

Recharge  the  unit  at  least 

three  lights  are  lit,  or  let  it 

cool  down  for  10  minutes 

until  the  temperature  is 

below  55

  before  you  can 

use it again. 

 

H.

 

Toxic and hazardous substances illustration 

 

Toxic and hazardous substances or elements 

Pb 

Hg 

Cd 

Cr(Ⅵ) 

PBB 

PBDE 

O: The content of this hazardous substance in all homogeneous materials of the component 

is below the limit requirements specified in the 2002/95/EC (Rohs) standard. 

 

I.

 

Precautions 

1.

 

Please be cautious when using it. 

2.

 

Please read the instructions carefully before use. 

3.

 

The product can only be used for starting 12V vehicles. It is prohibited to use 

it on 

equipment such as aircraft and ships. 

4.

 

Please do not use it if the clamp or the unit has any damage. 

5.

 

Prohibit using it as a car battery. 

Summary of Contents for KP120











Reviews: