To turn on the tool,press down the cocking button firstly and then the power switch button.(The
power switch button can be pressed down only after the locking button has been pressed.) After
the tool is turned on, the locking button can be released.
To turn off the tool, just release the power switch button.
CAUTION
Before turning the tool on, inspect the power switch to make sure it is easy to press and in the
right position.
Operation
First of all, place the tool on top of the work piece , resting it on the adjustable sole. Resting the
tool this way prevents the blades from touching the wood. Press the power switch.
Once the tool is up to speed, move the planer forward. When starting, exert more pressure at
the front of the planer; when finishing, exert more at the rear.
The routing or planing results depend on the speed and depth. The depth can be increased for
simple jobs.
Planing comerse
For routing as indicated in Figure 5,align the V-shaped prove in the front cover with the edge of
the piece being parked and then start planing.
Maintenance
CAUTION
Before pertorming any inspection or maintainance work, make sure the tool is switched off and
unplugged.
Replacing the brushes.
The brushes ust be inspected regularly and replaced when they are less than 5 mm long.
Keep the brushes clean to ensure that they can move freely inside the brush holders.
(B)
The planer depth can be adjusted from 0 to 3mm.
To increase the planing depth,turn the depth adjustment knob clockwise.
To decrease the planing depth, turn the adjusting knob counter clockwise.
CAUTION
Before using the tool,be sure that an external dust collecting device ( e.g.avacuum cleaner )has
been connected to the dust-collection opening of the tool properly.
Operating the switch
22)
23)
24)
25)
CAUTION
Only use the cutting head which is delivered together with original tool or available from the
manufacturer or it’s authorized service agent.
Always make sure that the tool is switched off and unplugged.Wait for the blades to come to a
full stop before removing or installing the blade.Loosen the three attachment screws with a
socket wrench.
You can remove either the blade alone or both the outer cover and the blade and then insert the
blade. The new blade must be the same size and weight as the old one; otherwise the
spindleWill vibrate, the cutting quality will be poor and the tool may be damaged.
To install the blade,mount on the guiding rule such that the blade edge touches the guide piece.
Then position the inner cover on the blade such that the curved end touches the rear of the
guiding rule over its entire length and then replace the screws. Tighten the screws of the inner
cover. Once they are light,mount the blade on the spindle such that the curved end of the inner
cover enters the respective spindle groove. Finally,tighten the three screws with the socket
wrench.
CAUTION
.
When mounting the blade on the spindle, the screws must be tight.Otherwise,serious personal
injury may result! Always check that the screws are tight and the blade is properly positioned.
The blade edge and the sole must be paralled. Otherwise the wood surface will not be flatted
and even. An example of a right and wrong installation is shown below.
(A)
TECHNICAL CHARACTERISTICS
Description and operation
This power planer is Class
Ⅱ。
Portable power tool equipped with double insulation and
single-phase series motor that has been designed primarily for smoothing and cutting wood.
Safety regulations
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
1)
2)
3)
4)
5)
6)
7)
8)
9)
10)
11)
12)
13)
14)
15)
16)
17)
18)
19)
20)
21)
Rags,clothes,cords,strings and similar objects should never be left around the work area.
Avoid cutting nails.Inspect for and remove all nails from the workpiece before operation.
Make sure that the bolts holding the blades are securely tightened before operation.
Make sure that the blades are not touched the workpiece before the switch is turned on.
Before using the tool on an actual workpiece,let it run for a few minutes.
When in operation, hold the tool firmly with both hands.Keep body at least 20cm away
from the tool at all times and keep hands away moving parts.
When you finish working,switch the tool off and set it with the front sole on a wooden block
so that the blade does not contact with any object.
Do not remove shaving with your hands. When the shaving deflector is jammed with
shavings,using a stick.
Warning : When using electric tools, basic safety precautions,
Including the following,should always be followed to reduce the risk of fire, electric shock
and personal injures
Read all these instructions before operating this product and save these instructions.
For safe operation:
Keep work area clean.
-Cluttered areas and bench invite injures.
Consider work area environment.
-Do not expose power tools to rain. Do not use power tools in damp or wet locations.Keep
work area well lit. Do not use power tools where there is risk to cause fire or explosion.
Guard against electric shock.
-Avoid body contacting with earthed or grounded surfaces(e.g.
pipes,radiators,ranges,refrigerators).
Keep children away.
-Do not let visitors touch the tool or extension cord.All visitors should be kept away from
area.
Store idle tools.,
-When not in use,tools should be stored in a dry ,high or locked up place.out of reach of
children.
Do not force the tool.
-Do not force small tools or attachments to do the job of a heavy duty tool.Do not use tools
for purposes not intended.
Use the right tool.
-Do not force small tools or attachments to do the job of a heavy duty tool.Do not use tools
for purposes not intended.
Dress Properly.
-Do not wear loose clothing or jewelery,they can be caught in moving parts.Rubber gloves
and non-skid footwear are recommended when working outdoors.Wear protecting hair
covering to contain long hair.
Use safety glasses.
-Also use face or dust ask if the cutting operation is dusty.
Connect dust extraction equipment.
-If devices are provide for the connection of dust extraction and
collection facilities ensure these are connected and properly used.
Do not abuse the cord.
-Never carry the tool by the cord or yank it to disconnect it from the socket.
Keep the cord away from heat,oil and sharp edges.
Secure work.
-Use clamps or a vice to hold the work. It is safer than using your hand and it frees both
hands to operate the tool.
Do not overreach
-Keep proper footing and balance at all times.
Maintain tool with care.
-Keep cutting tools sharp and clean for better and safer performance. Follow instructions
for lubrication and changing accessories. Inspect tool cord periodically and if damaged
have it repaired by an authorized service facility. Inspect extension cords periodically and
replace,if damaged.
Keep handles dry,clean and free from oil and grease.
Disconnet tools.
-When not in use, before servicing and when changing accessories such ad blades,bits
and cutters.
Removed adjusting keys and wreches.
-Form the habit of checking to see that keys and adjusting
wrenches are removed from the tool before turning it on.
Avoid unintentional starting.
-Do not carry a plugged-in tool with a finger when the switch is on. Ensure switch is off
when plugging in.
Use outdoor extension starting.
-When tool is used outdoors, use only extension cords intended for outdoor use .
Stay alert.
-Watch what you are doing.Use common sense. Do not operate tool when you are tired.
Check damaged parts.
-Before further use of the tool, a guard or other part that is damaged should be carefully
checked to determine that it will poerate properly and perform its intended function. Check
for alignment of moving parts,mounting other conditions that may affect its operation. A
guard or other part that is damaged should be properly repaired or replaced by an
authorized service centre unless otherwise indicated in this instruction manual.Have
defective switches replaced by an authorized service facility.Do not use the tool if the
switch does not turn it on and off.
Warning
-The use of some accessories or attachments,other than those
recommended in this instruction manual,may present a risk of
personal injury.
Let your tool be repaired by your tool repaired by a qualified person.
-This electric tool is in accordance with the relevant safety requirements.
Repairs should only be carried out by qualified persons using original spare parts,other-
wise this may result in considerable danger to the user.
Only use sharp blades.
Wait for complete run-down before putting the tool aside.
Hearing protection should be worn.
Removing and installing the blade.
Proper setting
Blade edge is even with sole.
Wrong setting
-Uneven lines
Reason: One of the two blade edges is not even with the sole.
-Sunken front
Reason: Blade edge and sole are not paralled. Blade is too low.
-Sunken back
Reason: Blade edge is higher than sole.
Adjusting the cut depth
Replace both brushes
at the same time. Remove the shaving deflector with a screwdriver, then take off the brush
cover, remove the brushes, instort the new brushes and replace the brush cover and shaving
deflector
Replacing the belt
When the belt is worm prevens the power tool from running property. It must be replaced.
Remove the belt cover by loosening the screws with a screws with a screwdriver. Then remove
the belt by turning it and pulling it out. Mount the new belt by turning it while pushing it in.
Mote: Make sure that the belt is properly installed on both pulleys.
When cleaning the tool; use only a brush, never water or other harsh liquids.
- 02 -
