To turn on the tool,press down the cocking button firstly and then the power switch button.(The
power switch button can be pressed down only after the locking button has been pressed.) After
the tool is turned on, the locking button can be released.
To turn off the tool, just release the power switch button.
CAUTION
Before turning the tool on, inspect the power switch to make sure it is easy to press and in the
right position.
Operation
First of all, place the tool on top of the work piece , resting it on the adjustable sole. Resting the
tool this way prevents the blades from touching the wood. Press the power switch.
Once the tool is up to speed, move the planer forward. When starting, exert more pressure at
the front of the planer; when finishing, exert more at the rear.
The routing or planing results depend on the speed and depth. The depth can be increased for
simple jobs.
Planing comerse
For routing as indicated in Figure 5,align the V-shaped prove in the front cover with the edge of
the piece being parked and then start planing.
Maintenance
CAUTION
Before pertorming any inspection or maintainance work, make sure the tool is switched off and
unplugged.
Replacing the brushes.
The brushes ust be inspected regularly and replaced when they are less than 5 mm long.
Keep the brushes clean to ensure that they can move freely inside the brush holders.
(B)
The planer depth can be adjusted from 0 to 3mm.
To increase the planing depth,turn the depth adjustment knob clockwise.
To decrease the planing depth, turn the adjusting knob counter clockwise.
CAUTION
Before using the tool,be sure that an external dust collecting device ( e.g.avacuum cleaner )has
been connected to the dust-collection opening of the tool properly.
Operating the switch
22)
23)
24)
25)
CAUTION
Only use the cutting head which is delivered together with original tool or available from the
manufacturer or it’s authorized service agent.
Always make sure that the tool is switched off and unplugged.Wait for the blades to come to a
full stop before removing or installing the blade.Loosen the three attachment screws with a
socket wrench.
You can remove either the blade alone or both the outer cover and the blade and then insert the
blade. The new blade must be the same size and weight as the old one; otherwise the
spindleWill vibrate, the cutting quality will be poor and the tool may be damaged.
To install the blade,mount on the guiding rule such that the blade edge touches the guide piece.
Then position the inner cover on the blade such that the curved end touches the rear of the
guiding rule over its entire length and then replace the screws. Tighten the screws of the inner
cover. Once they are light,mount the blade on the spindle such that the curved end of the inner
cover enters the respective spindle groove. Finally,tighten the three screws with the socket
wrench.
CAUTION
.
When mounting the blade on the spindle, the screws must be tight.Otherwise,serious personal
injury may result! Always check that the screws are tight and the blade is properly positioned.
The blade edge and the sole must be paralled. Otherwise the wood surface will not be flatted
and even. An example of a right and wrong installation is shown below.
(A)
TECHNICAL CHARACTERISTICS
Description and operation
This power planer is Class
Ⅱ。
Portable power tool equipped with double insulation and
single-phase series motor that has been designed primarily for smoothing and cutting wood.
Safety regulations
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
1)
2)
3)
4)
5)
6)
7)
8)
9)
10)
11)
12)
13)
14)
15)
16)
17)
18)
19)
20)
21)
Replace both brushes
at the same time. Remove the shaving deflector with a screwdriver, then take off the brush
cover, remove the brushes, instort the new brushes and replace the brush cover and shaving
deflector
Replacing the belt
When the belt is worm prevens the power tool from running property. It must be replaced.
Remove the belt cover by loosening the screws with a screws with a screwdriver. Then remove
the belt by turning it and pulling it out. Mount the new belt by turning it while pushing it in.
Mote: Make sure that the belt is properly installed on both pulleys.
When cleaning the tool; use only a brush, never water or other harsh liquids.
- 06 -
