background image

iWorx® HPU3

4

 

505-035, Effective: June 30, 2015 

© 2015 Taco Electronic Solutions, Inc.

REPRESENTATIONS AND WARRANTIES

This Document is subject to change from time to time at the sole discretion of Taco Electronic Solutions, Inc. All 
updates to the Document are available at www.taco-hvac.com. When installing this product, it is the reader’s responsi-
bility to ensure that the latest version of the Document is being used. 

iWorx® products shall only be used for the applications identified in the product specifications and for no other pur-
poses. For example, iWorx® products are not intended for use to support fire suppression systems, life support sys-
tems, critical care applications, commercial aviation, nuclear facilities or any other applications where product failure 
could lead to injury to person, loss of life, or catastrophic property damage and should not be used for such purposes.

Taco Electronic Solutions, Inc. will not be responsible for any product or part not installed or operated in conformity with 
the Document and instructions or which has been subject to accident, disaster, neglect, misuse, misapplication, inade-
quate operating environment, repair, attempted repair, modification or alteration, or other abuse. For further informa-
tion, please refer to the last page of this Document for the company’s Limited Warranty Statement, which is also issued 
with the product or available at www.taco-hvac.com.

APPLICABLE DOCUMENTATION

See the table below for additional documentation that may be applicable to this controller. 

Description

Audience

Purpose

iWorx® LCI Application Guide

, Docu-

ment No. 505-002

– Application Engineers
– Installers
– Service Personnel
– Start-up Technicians
– End user

Provides instructions for setting up and using 
the iWorx® Local Control Interface.

iWorx® LHP2 Application Guide

, Doc-

ument No. 505-024

– Application Engineers
– Installers
– Service Personnel
– Start-up Technicians
– End user

These controllers may operate in conjunction 
with the LHP2. Application manuals provide 
specific application information about these con-
trollers, including sequence of operation and 
configuration information.

iWorx® CCU2 Application Guide

Document No. 505-022

– Application Engineers
– Installers
– Service Personnel
– Start-up Technicians
– End user

These controllers may operate in conjunction 
with the CCU2. Application manuals provide 
specific application information about these con-
trollers, including sequence of operation and 
configuration information.

http://www.iWorxWizard.com

– Application Engineers
– Wholesalers
– Contractors

An on-line configuration and submittal package 
generator based on user input. Automatically 
generates bill of materials, sequence of opera-
tions, flow diagrams, wiring diagrams, points 
and specifications.

Additional 
Documentation

LonWorks FTT-10A Free Topology Transceiver User’s Guide,

 published by Echelon Corpo-

ration. It provides specifications and user instructions for the FTT-10A Free Topology Trans-
ceiver. See also: www.echelon.com/support/documentation/manuals/transceivers.

Summary of Contents for iWorx HPU3



































Reviews: