background image

D

O IT

O

NCE

. D

O IT

R

IGHT

.

®

TACO, INC.

, 1160 Cranston Street, Cranston, RI 02920

Telephone: (401) 942-8000

FAX: (401) 942-2360.

TACO (Canada), Ltd.

, 6180 Ordan Drive, Mississauga, Ontario L5T 2B3.

Telephone: 905/564-9422.

FAX: 905/564-9436.

Visit our web site at: 

http://www.taco-hvac.com

Printed in USA

Copyright 2005

TACO, Inc.

LIMITED WARRANTY STATEMENT

CASING

CERAMIC SEAT

AND CUP

FACEPLATE

BODY

BOLTS (4)

MOTOR ASSEMBLY

MECHANICAL SEAL

IMPELLER

BODY GASKET

Fig. 2: Exploded View of Pump

Taco, Inc. will repair or replace without charge
(at the company’s option) any product or part
which is proven defective under normal use
within three (3) years from the date of start-up or
three (3) years and six (6) months from date of
shipment (whichever occurs first).

In order to obtain service under this warranty, it
is the responsibility of the purchaser to promptly
notify the local Taco stocking distributor or Taco
in writing and promptly deliver the subject prod-
uct or part, delivery prepaid, to the stocking dis-
tributor. For assistance on warranty returns, the
purchaser may either contact the local Taco
stocking distributor or Taco. If the subject prod-
uct or part contains no defect as covered in this
warranty, the purchaser will be billed for parts
and labor charges in effect at time of factory
examination and repair.

Any Taco product or part not installed or operat-
ed in conformity with Taco instructions or which

has been subject to misuse, misapplication, the
addition of petroleum-based fluids or certain
chemical additives to the systems, or other
abuse, will not be covered by this warranty.

If in doubt as to whether a particular substance
is suitable for use with a Taco product or part, or
for any application restrictions, consult the
applicable Taco instruction sheets or contact
Taco at [401-942-8000].

Taco reserves the right to provide replacement
products and parts which are substantially sim-
ilar in design and functionally equivalent to the
defective product or part. Taco reserves the
right to make changes in details of design, con-
struction, or arrangement of materials of its
products without notification.

TACO OFFERS THIS WARRANTY IN LIEU OF
ALL OTHER EXPRESS WARRANTIES. ANY
WARRANTY IMPLIED BY LAW INCLUDING
WARRANTIES OF MERCHANTABILITY OR FIT-

NESS IS IN EFFECT ONLY FOR THE DURATION
OF THE EXPRESS WARRANTY SET FORTH IN
THE FIRST PARAGRAPH ABOVE.

THE ABOVE WARRANTIES ARE IN LIEU OF
ALL OTHER WARRANTIES, EXPRESS OR
STATUTORY, OR ANY OTHER WARRANTY
OBLIGATION ON THE PART OF TACO.

TACO WILL NOT BE LIABLE FOR ANY SPE-
CIAL, INCIDENTAL, INDIRECT OR CONSE-
QUENTIAL DAMAGES RESULTING FROM THE
USE OF ITS PRODUCTS OR ANY INCIDENTAL
COSTS OF REMOVING OR REPLACING
DEFECTIVE PRODUCTS.

This warranty gives the purchaser specific
rights, and the purchaser may have other rights
which vary from state to state. Some states do
not allow limitations on how long an implied
warranty lasts or on the exclusion of incidental
or consequential damages, so these limitations
or exclusions may not apply to you.

Summary of Contents for 1400 Series

Page 1: ...e installed on the pump suction and discharge to simplify future ser vice or replacement without draining the system 1 Using teflon tape or high quality thread sealant install Taco companion flanges on threaded pipe ends to ensure proper fit up and leak protection Instruction Sheet 1400 Series Hi Capacity Circulator 102 147 SUPERSEDES June 1 2003 EFFECTIVE August 15 2005 Plant ID 001 1183 INSTALLE...

Page 2: ...ccordance with local and national codes and regulations Electrical supply and grounding wires must be suitable for at least 90ºC 194ºF 1400 Series circulators are thermally protected and do not require external overload protection 1 Be sure all electrical power to pump is disconnected and locked out before proceeding with wiring 2 Loosen capacitor conduit box screw and remove cover 3 Attach approp...

Page 3: ...ce the face plate to its original posi tion Carefully tap the face plate evenly into the recess in the motor housing 7 Clean the impeller shaft before installing the new seal 8 Lubricate the impeller shaft with soapy water Do not install new seal on a dry impeller shaft or damage to seal may result 9 Slide the new carbon seal and spring assembly onto the shaft until it contacts the ceramic seal se...

Page 4: ... been subject to misuse misapplication the addition of petroleum based fluids or certain chemical additives to the systems or other abuse will not be covered by this warranty If in doubt as to whether a particular substance is suitable for use with a Taco product or part or for any application restrictions consult the applicable Taco instruction sheets or contact Taco at 401 942 8000 Taco reserves...

Reviews: