background image

27

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions.

(1) This device may not cause harmful interference.

(2) This device must accept any interference received, including interference that may 

cause undesired operation.

FCC  Rf  Radiated  Exposure  Statement:  This  device  has  been  evaluated  to  meet  general  Rf  exposure 
requirements  The device can be used in portable exposure conditions without Rf restrictions.

NOTE:

 THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE 

CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD 

VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.

FCC ID: IYFTTX850

This device complies with Industry Canada licence-exempt RSS standard(s). 1. Operation is subject to the following 

two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including 
interference that may cause undesired operation of the device.” 2. Changes or modifi cations not expressly approved by 
the party responsible for compliance could void the user’s authority to operate the equipment.

This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. The device can be 

used in portable exposure conditions without Rf restrictions.

Avis d’Industrie Canada

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. 
L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) 
l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en 
compromettre le fonctionnement. Cet appareil numérique ne dépasse pas les Rèlements sur l’interférence radio par un 

appareil numérique de classe B stipulées dans les Règlement sur l’interférence redio d’industrie Canada.

2.Les changements ou modifi cations de cette unité non expressément approuvés par la partie responsable de la 
conformité pourraient annuler l’autorité de l’utilisateur à utiliser l’équipement.

IC RF Déclaration sur la radioexposition:

Cet appareil est conforme avec I’exposition aux radiations IC Défi nies pour un environnement non contrôlé.  L’appareil 
peut être utilisé dans des conditions d’exposition portatifs sans restrictions Rf.

Instructions for Disposal of Waste Equipment by Private Users in the European Union: This symbol on the 
product or its packaging indicates this product must not be disposed of with other household waste. Instead, 
it is the user’s responsibility to dispose of their waste equipment by handing it over to a designated collection 
point for the recycling of waste electrical and electronic equipment. The separate collection and recycling 
of your waste equipment at the time of disposal will help to conserve natural resources and ensure that it 

is recycled in a manner that protects human health and the environment. For more 
information about where you can drop off your waste equipment for recycling, please 
contact your local city offi ce, your household waste disposal service or location where 

you purchased the product.

FCC STATEMENT

INDUSTRY CANADA NOTICE

CE COMPLIANCE INFORMATION FOR THE EUROPEAN UNION

Summary of Contents for TACJ2850





























Reviews: