background image

7

IMPORTANT WARNINGS REGARDING LIPO BATTERY USE

NEVER ATTEMPT TO CARE FOR LITHIUM-POLYMER (LiPo) CELLS 
IN THE SAME WAY AS OTHER BATTERY TYPES! 

LiPo cells are much 

more sensitive and volatile than NiCd or NiMH batteries. Misuse and 
overcharge can quickly result in LiPo cells getting hot and/or swelling, 

which could lead to 

VIOLENT EXPLOSION AND/OR FIRE

 and serious personal 

injury and property damage.

   NEVER

 attempt to recharge other battery types except 1S LiPo cells with this 

built-in charger.

   NEVER

 continue to charge or use LiPo cells if they start to swell, and become 

overly warm to the touch. Failure to follow this guideline could cause the battery 
to become hot and explode or ignite!!

   ALWAYS

 disconnect the battery from the charger immediately if the battery 

becomes hot! Allow the battery to cool before use.

   NEVER

 allow water, moisture or foreign objects into the Tx/charger.

   NEVER

 leave the room where a battery is being charged.

   NEVER

 place the Tx/charger or battery on a fl ammable surface or near a 

fl ammable object during the charge process. Keep away from carpets, cluttered 
workbenches, etc.

   ALWAYS

 have a “class D” fi re extinguisher available when handling LiPo batteries.

   

If a LiPo cell leaks fl uid, do not get fl uid on the skin, in the eyes or mouth, etc. If 
you make contact with fl uid from a LiPo battery, rinse the affected area well with 
water and seek immediate medical care.

LINK THE RECEIVER TO THE TRANSMITTER

This link ensures sole communication between this Tx and the receiver, and 

prevents other transmitters from controlling the model. If it’s necessary to re-link the 
receiver to the transmitter:

 1. 

 

Switch on the Tx.

 2. 

 

Connect the battery to the Rx. See SERVOS AND ACCESSORIES on page 

12 for recommendations.

 3. 

 

The Rx LED on the Rx will turn on, indicating the Rx is bound to the Tx. On 

some receivers, you will have to push and hold the link button for 3 seconds.

 4. 

 

Test for proper Tx / Rx functionality in the next section. If the system did not 

become properly linked, repeat steps 1-3 above.

Summary of Contents for TTX403

















Reviews: