background image

13

8.  Anytime power is to be removed from the radio system, it’s important to shut 

down power in the aircraft 

fi rst

. Otherwise, the aircraft could become out of 

control and cause a safety hazard! Move the throttle stick and throttle trim 
lever to minimum position to stop the glow engine or shut down the ESC. 
Once the propeller has stopped rotating, shut off the ON/OFF power switch 
in the model, and disconnect the power battery from the ESC in electric 
airplanes. Then turn off the power switch in the Tx.

FLYING THE AIRCRAFT

1.  Once all setup procedures have been confi rmed, and power has been 

removed from the model and transmitter, re-attach the propeller to the model.

IMPORTANT:

  

Be very careful to stay clear 
from moving propellers!!

2.  Make sure the glow engine fuel tank has an adequate amount of fuel, or 

power batteries for electric airplanes are fully charged.

3.  Move the Tx throttle stick to the minimum position, then turn on the Tx power 

switch. Turn on the power switch in the model or connect the fl ight battery.

4.  During the fi rst fl ight, it might be necessary to re-trim the aileron, elevator, 

and rudder channels to allow the airplane to sustain smooth, even fl ight. If 
further adjustments are required on the ground, make sure to turn off the 
engine or ESC/motor before making such adjustments.

5.  When the fl ight is completed, remove power from the system as described 

before. Shut down power to the electronic speed control or glow engine fi rst, 
then the receiver, and fi nally the transmitter.

SAFETY GUIDE

The Academy of Model Aeronautics (AMA) has established an Offi cial Safety 
Code. Model fl ying 

MUST 

be in accordance with this Code in order for AMA Liability 

Protection to apply. All questions relating to the AMA Safety Code, liability insurance 
program, and other offi cial AMA information can be attained from the AMA:

Academy of Model Aeronautics

5161 East Memorial Drive
Muncie, Indiana 47302

(765) 287-1256 – Business
(765) 289-4248 – Fax
(800) 435-9262 – Membership Services

http://www.modelaircraft.org

http://www.modelaircraft.org/fi les/Memanual.PDF

Summary of Contents for TTX600

























Reviews: