Tait T2020II Operator'S Manual Download

Page: 16 / 16

Appendix

Maintenance of your T2020

The T2020

requires no regular maintenance, other than ensuring that all cables and con-

nections are secure, and that no damage has occurred to the antenna or wiring.

Troubleshooting

If the front panel indicators do not light up when you turn the radio on, it is likely that no power

is reaching the T2020

. Check the following:

Is the power connector firmly plugged into the rear of the T2020

Are the in-line fuses in good condition?

Is the power cable securely connected to the vehicle battery or power supply?

If all appears to be in order, then contact your Tait dealer for further assistance.

Despatcher Operation

The T2020

can also be used for despatcher operation, mounted on top of its companion T2008

power supply, which is available separately. Consult your Tait dealer for more information.

Radio Unit

T2008 Power

Supply

PQRS

WXYZ

STAT

T2000

Power Supply

T2000

Tait Electronics has made every effort to ensure the accuracy of information in this manual.

However, Tait Electronics reserves the right to update the radio and / or this manual

without notice.

Summary of Contents for T2020II

















Search results

Summary of Contents for T2020II

Reviews:

Related manuals for T2020II

Brands by name

Popular brands

Tait T2020II, Operator'S Manual

Search results

Summary of Contents for T2020II

Reviews:

Related manuals for T2020II

Brands by name

Popular brands