background image

 

42

Tait General Software Licence Agreement

TM9300/TM9400 Installation Guide

© Tait Limited December 2015

solely in connection with Licensee's use of the

Designated Products for the useful life of the

Designated Products. This Agreement does not

grant any rights to source code.

3.2. If the Software licensed under this Agree-

ment contains or is derived from Open Source

Software, the terms and conditions governing

the use of such Open Source Software are in the

Open Source Software Licenses of the copy-

right owner and not in this Agreement. If there

is a conflict between the terms and conditions of

this Agreement and the terms and conditions of

the any applicable Open Source Software

Licenses, the terms and conditions of the Open

Source Software Licenses will take precedence.

For information about Open Source Compo-

nents contained in Tait products and the related

Open Source licenses, see:

 

http://support.taitradio.com/go/opensource

Section 4 LIMITATIONS ON USE

4.1. Licensee may use the Software only for

Licensee's internal business purposes and only

in accordance with the Documentation. Any

other use of the Software is strictly prohibited.

Without limiting the general nature of these

restrictions, Licensee will not make the Soft-

ware available for use by third parties on a "time

sharing," "application service provider," "ser-

vice bureau" basis, or for any other similar com-

mercial rental or sharing arrangement. 

4.2. Licensee will not, and will not directly or

indirectly allow or enable any third party to: (i)

reverse engineer, disassemble, extract compo-

nents, decompile, reprogram, or otherwise

reduce the Software or any portion thereof to a

human perceptible form or otherwise attempt to

recreate the source code; (ii) modify, adapt, cre-

ate derivative works of, or merge the Software;

(iii) copy, reproduce, distribute, lend, or lease

the Software or Documentation to any third

party; (iv) grant any sublicense or other rights in

the Software or Documentation to any third

party; (v) take any action that would cause the

Software or Documentation to be placed in the

public domain; (vi) remove, or in any way alter

or obscure any copyright notice or other notice

of Tait or third-party licensor’s proprietary

rights; (vii) provide, copy, transmit, disclose,

divulge or make the Software or Documentation

available to, or permit the use of the Software

by, any third party or on any machine except as

expressly authorized by this Agreement; or

(viii) use, or permit the use of, the Software in a

manner that would result in the production of a

copy of the Software by any means whatsoever

other than what is permitted in this Agreement.

Licensee may make one copy of the Software to

be used solely for archival, back-up, or disaster

recovery purposes; provided that Licensee may

not operate that copy of the Software at the same

time as the original Software is being operated.

Licensee may make as many copies of the Doc-

umentation as it may reasonably require for the

internal use of the Software.

4.3. Unless otherwise authorized by Tait in writ-

ing, Licensee will not, and will not enable or

allow any third party to: (i) install a copy of the

Software on more than one unit of a Designated

Product; or (ii) copy or transfer Software

installed on one unit of a Designated Product to

any other device. Licensee may temporarily

transfer Software installed on a Designated

Product to another device if the Designated

Product is inoperable or malfunctioning. Tem-

porary transfer of the Software to another device

must be discontinued when the original Desig-

nated Product is returned to operation and the

Software must be removed from the other

device. 

4.4. Licensee will maintain, during the term of

this Agreement and for a period of two years

thereafter, accurate records relating to this

license grant to verify compliance with this

Agreement. Tait, or a third party nominated by

Tait, may inspect Licensee’s premises, books

and records, upon reasonable prior notice to

Licensee, during Licensee’s normal business

hours and subject to Licensee's facility and

security regulations. Tait is responsible for the

payment of all expenses and costs of the inspec-

tion, provided that Licensee shall indemnify

Tait for all costs (including audit costs and legal

costs on a solicitor client basis) if Licensee has

breached the terms of this Agreement. Any

information obtained by Tait during the course

of the inspection will be kept in strict confi-

dence by Tait and used solely for the purpose of

verifying Licensee's compliance with the terms

of this Agreement.

Section 5 OWNERSHIP AND TITLE

Tait, its licensors, and its suppliers retain all of

their Intellectual Property Rights in and to the

Software and Documentation, in any form. No

rights are granted to Licensee under this Agree-

ment by implication, estoppel or otherwise,

except for those rights which are expressly

granted to Licensee in this Agreement. All Intel-

lectual Property developed, originated, or pre-

pared by Tait in connection with providing the

Software, Designated Products, Documenta-

tion, or related services, remains vested exclu-

sively in Tait, and Licensee will not have any

shared development or other Intellectual Prop-

erty Rights.

Section 6 LIMITED WARRANTY; 

DISCLAIMER OF WARRANTY 

6.1. The commencement date and the term of

the Software warranty will be a period of one (1)

year from Tait shipment of the Software. If

Licensee is not in breach of any obligations

under this Agreement, Tait warrants that the

unmodified Software, when used properly and

in accordance with the Documentation and this

Agreement, will be free from a reproducible

defect that eliminates the functionality or suc-

cessful operation of a feature critical to the pri-

mary functionality or successful operation of

the Software. Whether a defect has occurred

will be determined solely by Tait. Tait does not

warrant that Licensee’s use of the Software or

the Designated Products will be uninterrupted,

error-free, completely free of Security Vulnera-

bilities, or that the Software or the Designated

Summary of Contents for TM9300 DMR















































Reviews: