749161-101
Made in China
2014
5.
With all remote control sets turned on, use any remote control and press the FUNCTION and RESET button at the same time
for about 2 seconds, all sets should return to function 1. If this did not work please try it again.
6.
Press the FUNCTION button until you have selected the desired light function effect.
7.
For best results, all sets should be turned on or off at the same time. If connected to multiple outlets, use the
on/off feature on the remote. If connected to the same switched outlets, you can turn on or off power to the
outlet or by using the remote.
TIP –
If you want to return all the sets back to Function 1 at any time, just push both the “FUNCTION” and “RESET”
buttons at the same time for about 2 seconds until the set returns to Function 1. This resets the units back to Function
1 (Chase-Fade between colors) so you can start over in the order of the functions.
Additional Notes for Synchronizing Multiple Sets:
A. When multiple light sets are lighted, pressing the FUNCTION button will change all sets to the next pattern.
B. These are Radio Frequency controlled devices. All sets within the effective range will be affected and controlled using any one
remote.
C. It is not possible to have different lighting functions on different sets in the same remote control range area.
D. If used with a mechanical / digital timer, only one timer must control all sets. In this case, do not turn sets off by using the
remote or the sets will not turn on with the timer.
E. Due to component tolerances, there may be cycle time differences between sets.
WARNING:
Do not expose the remote control to moisture. If used outdoors, do not bring outside when raining or snowing, use remote
from indoors instead.
Remove battery when not used for extended periods of time, or when depleted.
Dispose of battery properly by following directions on batteries.
Use only 12V Alkaline battery type 23A for replacement, use of other batteries may damage remote.
Troubleshooting Instructions
.
If lights do not change function or turn off or on when a button is pushed:
1.
Check that the red LED light on the remote is illuminating and not dim:
a.
Check that battery is inserted properly (+ and -) and making contact (typically the LED would not be illuminating
in this condition), see battery installation details for correct battery installation.
b.
Clean battery and remote terminals.
c.
Replace battery with a new one, see battery installation details for correct battery installation.
2.
Make sure antenna is up and fully extended.
3.
Move away from other items that may cause interference, such as cell phones, 2-way radios, microwave ovens,
computers, Wi-Fi access points, etc.
4.
Make sure you are close enough to the light set control box.
5.
Make sure light string has power:
a.
Make sure power is on at the outlet (try a different product on the outlet to ensure power is on)
b.
Make sure outlet is not powered by a dimmer (if it is move set to a different outlet)
c.
Make sure outlet is not on a timer (if it is move set to a different outlet)
d.
Reset Ground Fault Circuit Interrupter (GFCI) in case it accidentally tripped.
6.
Unplug light string plug for 1 minute and plug back into powered outlet and retry.
7.
If used on a timer controlled circuit, make sure the timer is rated for use with Compact Fluorescent bulbs (CFL) as some
timers will not work properly with electronics.
8.
If set stays in the “Chase – Fade between colors” mode (Function 1) – check to make sure that the remote is not located
where both the “FUNCTION” and “RESET” buttons are pressed at the same time - relocate remote so buttons are not
pushed during use.
If the remote only works at a very short distance (for example, right next to the light set), follow steps 1 – 3 above.
If sets do not turn on when power is turned on to the set (when plugging into an outlet, a timer turns it on, or switch controlling the
outlet is turned on), try pushing the “POWER”
button as it may have been turned off using the remote the last time it was used
(remember, this product will remember the last function it was turned off at, including if the remote was used to turn the set off).
If the battery in the remote drains and becomes depleted very quickly, then the remote is being placed where one (or more) of the
buttons on the remote are being continually pushed (such as placing an item on top of the buttons, or storing the remote upside
down, etc.). Place the remote such that the buttons are not pushed.
TIP – If you want to return the set back to Function 1 at any time, just push both the “FUNCTION” and “RESET” buttons at the same
time for about 2 second until the set returns to Chase – Fade between colors. This resets the units back to Function 1 (Chase – Fade
between colors) so you can start over in the order of functions.
