2. PRESENTATION
2.2 Function of E1800
- Lift sensor
There are lift sensors located between the top and middle
- Tilt sensor
There are tilt sensors installed on the mower too, when
mower is tilted over 30 degrees in any direction, it
the
seconds.
stops working within 2
- Bump sensor
The whole top cover is movable. Both front and side
of mower equipped with bump sensors that will
activate when the mower strikes solid, fixed object when
that object is at least 6cm in vertical height from the
supporting surface of the mower. When the bump sensor
- Rain sensor
There are two rain sensors located on the
mower.
The mower will go back
to the charging station
when it's raining.
automatically
Turn on: the mower will go back home if it is raining.
Turn off: the mower will go on mowing when it is raining.
- Wifi
cover. If the mower is lifted from ground, it will stops
working within 1 second.
activated, the mower will back up for working.
Rain sensors can be selected ON/OFF from APP.
- Area working time setting(mowing schedule)
-
Touch
sensor
Set up one week (From Monday to Sunday, once for
schedule from APP. This function
each day) cutting
- Cutting width: 21cm
- Easy cutting height adjustments
The cutting height could be adjusted on the mower
.
- Auto recharge system
When the mower senses a low battery situation, it will
shut off the cutting motor and search for the virtual wire.
Once found it will follow the virtual wire to the charging
station for recharge automatically. Once charging is
complete, the mower will back up a few centimeters
ready to go again in stand by mode.
- Emergency stop switch
There is an emergency button located on the top of
color.
mower and in red
should be used together with
Area location setting
.
- Two cutting modes
There are two cutting modes of the mower, go straight
efficiency).
and go circle (high
In Auto, mower selects cutting mode intelligently.
It goes straight if the grass is sparse or it has be cut off,
long.
and it goes circle if the grass is dense or
In manual mode, the mower will go where you direct it.
-
use 100m-600m of virtual wire). The
wire. (we suggest to
station, the virtual
mower will follow virtual wire to charging
on the virtual wire
wire acts as a virtual fence. It will get
wire and starts cutting inside.
- Mower stops working if virtual wire is cut off or
power off.
charging station is
If virtual wire is cut or broken, or the charging station
loose power, the mower will stop working within 3 seconds
- Four steps to safely start the mower
- Overload protect
The cutting motor and running motor are monitored
continuously during operation for any situation that
may cause these motors to over-load.
In the event this is detected, the mower stops operating.
- Waterproof
Waterproof design, there is an inner cover under top
inside parts from humidity.
cover which protect
Virtual wire
The robot lawn mower can't be operated without a virtual
- Gyroscope
The mower has gyroscope to keep it going straight on
until it meets charging sheets, then it gets off from virtual
The waterproof class is I
- Area location setting(Subarea setting)
You can select Subareas for the mower to cut. This works
well for large lawn. See Section 6.4.
- Different languages selection on App.
- 4 -
P54.
Connect charging station with power supply by charger
and make sure the recharging light is in green color.
2. Connect virtual wire to charging station and make sure
it is in good connecting(virtual wire light in colorless).
3. Turn on the power button
- Range
There are four range options, user can choose the
distance when robot hit virtual wire according the
condition of different lawns.
1.
The Android user search “EGROBOT” in the Google
Store to download the application.
The IOS user can search “EGROBOT” in the Apple
inclines.
Play to download the application.
Press it to turn on the mower .
Press it again to turn off the mower.
Touch
the
handle
when
the
mower
is
cutting
,
it
will
cease
function
.
bottom cover cutting height adjustment knob via the
equipped spanner.
4. Press emergency button and start auto mode.
