background image

5

USE

5.13 Recharging

- The mower could goes back to recharging automatically if it is power
   less. Or press the Home button on the charging station, the mower also 
   goes  back to station for recharge.

- The mower also can  recharges  by charger directly.

Steps as follow:

 1. Press the clamshell and open it.

 2. Unscrew the cap of charging
     terminal.

 3. Insert charger and screw the 
     knob.

 4. Connect the charger to power 
     supplier. 

Recharge Voltage:24V (Lead-acid battery) / 29.4V(Lithium battery) 
Recharge current: 2A

Match the slop then
screw it!

-

P41

-

6

Maintenance and storage

6. MAINTENANCE AND STORAGE

- During maintenance operations, use the individual protections indicated
  by the Manufacturer , especially when intervening on the blade.

- Before performing maintenance operations, make sure that the robot 
  has stopped in safety conditions.

PROGRAMMED MAINTENANCE INTERVALS CHART

See “Robot
cleaning”

See “Blade
replacement”

If the fuse is burned
down

See “Fuse
replacement”

Robot

Carry out cleaning

See “Robot
cleaning”

6.1 Robot cleaning

    1.Stop the robot in safety conditions.
  

     2. Wear protective gloves.

Frequency

Component

Type of operation

Reference

Every week

Every month

Blade

Fuse

Clean and check the
efficiency of the 
blade

If the blade is bent due
to an impact or if it is
worn-out, replace it.

-

P42

-

The charger is not water-proof therefore it must be located on 
a place which is dry and ventilated.

WA R N I N

Summary of Contents for L2700































Reviews: