Taizhou Tianchen Intelligence & Electrics S520, User Manual

2. PRESENTATION

2.2 Function of S520

-  Lift sensor

   There are lift sensors located between the top and middle

-  Tilt sensor

   There are tilt sensors installed on the mower too, when 

mower is tilted over 30 degrees in any direction, it    

the 

seconds.

stops working within 2 

-  Bump sensors

The whole top cover is movable. Both front and the two

    sides of mower equipped with bump sensors that will
    activate when the mower strikes solid, fixed object when
    that object is at least 6cm in vertical height from the 
    supporting surface of the mower. When the bump sensor

-  Rain sensors

   There are two rain sensors located on the control panel 

   at

to the 

 top cover of mower. The mower will go back 

   charging station automatically when it's raining.

   Turn on: the mower will go back home if it is raining.
   Turn off: the mower will go on mowing when it is raining.

-  Touch sensor

   Touch the handle when the mower is cutting, it will 

second.

 cease function within 0.5 

-  Wireless remote controller

cover. If the mower is lifted from ground, it will stops 

 working within 1 second.

     activated, the mower will stop movement in that 

the obstacle.

direction and reverse itself away from 

    Rain sensors can be selected ON/OFF from control panel.

-  Mowing schedule

   Set up one week (From Monday to Sunday, once for  
   

schedule from control panel. This  

each day) cutting 

-  Anti-theft function

   Mower has password protection option to guard against   

theft. What's more, the mower can not be turned on 

-  Cutting width: 28cm

-  Easy cutting height adjustments

   2.5cm-6cm selected with one dial.

-  Auto recharge system

   When the mower senses a low battery situation, it will 
   

shut off the cutting motor and search for the virtual wire. 

Once found it will follow the virtual wire to the charging 
station for recharge automatically. Once charging is   

   complete, the mower will back up a few centimeters 
   ready to go again in stand by mode.  

-  Emergency stop switch

   There is an emergency switch located on the top of 

color. When pressed, the mower will

mower and red in 

 shut down immediately. Rotate the switch clockwise to

function should be used together with AREA function. 

without a charging station.

   release it. 

-  Two cutting modes

   There are two cutting modes of the mower, go straight 

 efficiency). 

and go circle (high

   In Auto, mower selects cutting mode intelligently. 
   It goes straight if the grass is sparse or it has be cut off, 

 long.

and it goes circle if the grass is dense or

   In manual mode, the mower will just go were you direct it. 

-  Pressure sensors

The pressure sensors located on the top cover. If a child

or some thing rides or sits on the mower, it stops
working within 1 second. 

-  

use 100m-600m of virtual wire). The 

wire. (we suggest to 

station, the virtual

mower will follow virtual wire to charging 

on the virtual wire

 wire acts as a virtual fence. It will get 

   wire and starts cutting inside.

-  Mower stops working if virtual wire is cut off or 
   

power off.

charging station is 

   If virtual wire is cut or broken, or the charging station  
   

loose power, the mower will stop working within 3 seconds

-  Four steps to safely start the mower

   There are four necessary steps to start the mower: 

-  Overload protect

   The brushless cutting motor and each of the two running

are monitored continuously during operation for 

 motors 

cause these motors to over-load

any situation that may 

    In the event this is detected, the mower stops operating.

-  Waterproof

   Waterproof design, there is an inner cover under top   

inside parts from humidify. 

cover which protect 

-  LCD display

Virtual wire

   The robot lawn mower can't be operated without a virtual 

 LINE (virtual wire) can be selected ON/OFF from control 

-  Electronic compass

The mower has compass navigation system to keep it 

   until it meets charging sheets, then it gets off from virtual  

 The waterproof class is I 

-  Subarea setting

You can select Subareas for the mower to cut. This works

well for large lawn. See Section 5.11. 
This function should be used together with 

schedule

.

-  Different languages selection.

- 4 -

P55.

panel. 

   1. Connect charging station with power supply by charger 
       and make sure the recharging light is in green color. 
   2. Connect virtual wire to charging station and make sure 
       it is in good connecting(virtual wire light in colorless). 
   3. Turn on the power button and release the emergency 
       switch. 
   4. Input password if selected and select mode. 

going straight on inclines.

-  Range

There are four range options, user can choose the 

distance when robot hit virtual wire according the 
condition of different lawns.