CHAPTER 8 PARAMETER SETTING
86
26. Preset Halt (Data)
27. Preset Halt (Design)
28. Preset Halt (Lubrication)
29. Preset Halt (Just before End Code)
30. Language
When frame moving amount reaches the set value,
it will make the machine stop automatically.
Code number “1D2” will be displayed at
stop of the machine.
"0" makes no stop.
(0 ~ 99999 cm)
0
-
Yes
0.8
0
0
0
0
No
Japanese
21. Select Under T. Trimming [mm]
( 0, 5, 10, 20, 30, A, )
( -, 1, 2, )
( No, Yes, )
24. Tie/Return Stitch Length [mm]
( 0.6, 0.8, )
( 0 ~999999 st., )
( 0 ~99999 cm, )
( 0 ~999 Designs, )
( 0 ~99 * 10000 st., )
29. Preset Halt (Just before End Code)
( No, Yes, )
( English, Japnese, Other, )
0
Numerical key
(GC07)
When embroidered designs reach the set value, it
makes the machine stop automatically.
Code number “1D2” will be displayed at
stop of the machine.
"0" makes no stop.
(0 ~ 999 Designs)
0
-
Yes
0.8
0
0
0
0
No
Japanese
21. Select Under T. Trimming [mm]
( 0, 5, 10, 20, 30, A, )
( -, 1, 2, )
( No, Yes, )
24. Tie/Return Stitch Length [mm]
( 0.6, 0.8, )
( 0 ~999999 st., )
( 0 ~99999 cm, )
( 0 ~999 Designs, )
( 0 ~99 * 10000 st., )
29. Preset Halt (Just before End Code)
( No, Yes, )
( English, Japnese, Other, )
0
Numerical key
When the stitch counter reaches the set value, it
will make the machine stop automatically.
Setting value multiplied by 10000 stitches
Code number “OIL” will be displayed at
stop of the machine.
"0" makes no stop.
It is effective when “36. Lubrication” is set
to “No”.
(0 ~ 99 * 10000st.)
0
-
Yes
0.8
0
0
0
0
No
Japanese
21. Select Under T. Trimming [mm]
( 0, 5, 10, 20, 30, A, )
( -, 1, 2, )
( No, Yes, )
24. Tie/Return Stitch Length [mm]
( 0.6, 0.8, )
( 0 ~999999 st., )
( 0 ~99999 cm, )
( 0 ~999 Designs, )
( 0 ~99 * 10000 st., )
29. Preset Halt (Just before End Code)
( No, Yes, )
( English, Japnese, Other, )
0
Numerical key
It makes the machine stop automatically just
before end of embroidery.
It is possible to perform frame back after
stop of the machine.
Yes
To perform automatic stop
No
Not to perform automatic stop
(Yes/No)
0
-
Yes
0.8
0
0
0
0
No
Japanese
21. Select Under T. Trimming [mm]
( 0, 5, 10, 20, 30, A, )
( -, 1, 2, )
( No, Yes, )
24. Tie/Return Stitch Length [mm]
( 0.6, 0.8, )
( 0 ~999999 st., )
( 0 ~99999 cm, )
( 0 ~999 Designs, )
( 0 ~99 * 10000 st., )
29. Preset Halt (Just before End Code)
( No, Yes, )
( English, Japnese, Other, )
No
Select display language of the screen.
“Other” becomes different language depend-
ing on specification.
When setting was switched to “Other”, turn
on the power again.
(English, Japanese, Other)
0
-
Yes
0.8
0
0
0
0
No
Japanese
21. Select Under T. Trimming [mm]
( 0, 5, 10, 20, 30, A, )
( -, 1, 2, )
( No, Yes, )
24. Tie/Return Stitch Length [mm]
( 0.6, 0.8, )
( 0 ~999999 st., )
( 0 ~99999 cm, )
( 0 ~999 Designs, )
( 0 ~99 * 10000 st., )
29. Preset Halt (Just before End Code)
( No, Yes, )
( English, Japnese, Other, )
Japanese
Summary of Contents for TFHX Series
