Takagi T-D2-IN / 510 Installation Manual And Owner'S Manual Download

Page: 4 / 44

INTRODUCTION

•

This manual provides information necessary for the

installation, operation, and maintenance of the water

heater .

•

The model description is listed on the rating plate which

is attached to the side panel of the water heater .

•

Please read all installation instructions completely before

installing this product .

•

If you have any problems or questions regarding

this equipment, consult the manufacturer or its local

representative or call an HVAC technician in your area .

•

This equipment is an on-demand, tankless water heater

designed to efficiently supply endless hot water for your

needs .

•

The T-KJr2-IN / 110, T-K4-IN / 310, & T-D2-IN / 510

models are to be installed indoors only (direct-vent

convertible) .

•

The principle behind tankless water heaters is simple:

Exhaust vent

collar

Burners

Cold Water

Inlet

Fan motor

Thermistor

Hot Water

Outlet

Heat

exchanger

Thermistor

Flow sensor

Computer

board

Gas Valves

Gas

Inlet

Flow adjustment

valve

* This diagram illustrates tankless water heater design

concepts only and does not accurately represent the

water heater’s physical description .

1 . A hot water tap is turned on .

2 . Water enters the heater .

3 . The water flow sensor detects the water flow .

4 . The computer initiates the fan motor and sends a signal

to the igniter to create an ignition spark .

5 . The igniter starts and the gas valve opens and flames

appear within the burner chamber .

6 . Water circulates through the heat exchanger and then

gets hot .

7 . Using thermistors to measure temperatures throughout

the water heater, the computer modulates the gas and

water valves to ensure proper output water temperature .

8 . When the tap is turned off, the unit shuts down .

SAFETY GUIDELINES

Safety Definitions

DANGER

Indicates an imminently hazardous situation

which, if not avoided, will result in death or

serious injury .

WARNING

Indicates an imminently hazardous situation

which, if not avoided, could result in death or

serious injury .

CAUTION

Indicates an imminently hazardous situation

which, if not avoided, could result in minor or

moderate injury .

General

1 . Follow all local codes, or in the absence of local codes,

follow the most recent edition of

CSA B149.1 Natural

Gas and propane Installation Code

2 . Properly ground the unit in accordance with all local

codes or in the absence of local codes, with

CSA C22.1

Canadian Electrical Code Part 1

3 . Carefully plan where you intend to install the water

heater . Please ensure:

•

Your water heater will have enough combustible air

and proper ventilation .

•

Locate your heater where water leakage will not

damage surrounding areas . (Please refer to pg . 6,7 .)

4 . Check the rating plate for the correct GAS TYPE,

GAS PRESSURE, WATER PRESSURE and ELECTRIC

RATING .

* If this unit does not match your requirements, do not

install . Consult with the manufacturer .

5 . If any problem should occur, turn off all hot water taps

and turn off the gas . Then call a trained technician or the

Gas Company or the manufacturer .

Summary of Contents for T-D2-IN / 510













































Search results

Summary of Contents for T-D2-IN / 510

Reviews:

Related manuals for T-D2-IN / 510

Brands by name

Popular brands

Takagi T-D2-IN / 510, Installation Manual And Owner'S Manual

Search results

Summary of Contents for T-D2-IN / 510

Reviews:

Related manuals for T-D2-IN / 510

Brands by name

Popular brands