background image

15

An electronic alarm (2 beeps) will sound to announce that time is up when the time set for the Mist 
Operation has elapsed (the time display will be at 0) and the cleaning time period (2 minutes) will begin. 
When the cleaning time period ends, the electronic alarm will sound (3 beeps) and the heat maintenance 
period (20 minutes) will begin.(The keep lamp will light up)

*In the case where Cleaning has been set to OFF when making the settings, the heat maintenance period 
  begins immediately after the completion of the Mist Operation.

Unattended Time Count

*After the cleaning operation has ended, the Unattended 
  Time  (including the cleaning time) will be displayed 
  by flashing it on and off.

Fastener

Removing the Face Guard

1. Open the Upper Cover.

2. Press on the fastener button and loosen the crossed 
    strap.

3. Loosen the Face Guard and move it away 
    from the customerís head.

4. Close the Upper Cover, then lift up the 
    Hood and move the Main Unit.

When using the machine consecutively with multiple customers, check the water 
level in the Water Container and the Drain Tank before using it. 

Turning off the power

Turn off the Power Switch after completing operations.
*Turning off the power will invalidate the operating  mode 
  settings.

After the Mist Operation is complete

Caution

Check to make sure the Face Guard 
has been removed before raising the 
Hood.

Summary of Contents for Ak-200





















Reviews: