background image

3

Caution

Use the handle to move the unit.

Do not try to move the unit using the stand or the 
hood.
This may cause it to tip over.

Put the hood up when moving the 
main unit.

Failure to do so may lead to it hitting customers 
or equipment.

Do not shake the unit while it is 
in operation.

This may cause water leakage or overflow.

Do not put boiling water in the 
Water Container.

This will cause the internal section to heat up and 
may lead to malfunctions.

Promptly wipe off any chemical 
spills.

When treatment, permanent, or coloring chemicals 
come into contact with the unit, use a damp cloth 
to wipe them off as soon as possible. Failure to do 
so may cause surface staining or discoloration.

Do not move the main unit using the 
Nape Bar.

This may lead to the unit tipping over and may cause 
damage to the Nape Bar.

Do not apply force to the Hood.

This may lead to the unit tipping over and may 
cause damage to the Hood.

Do not put anything other than purified 
water made for the steamer/purified 
water into the Water Container.

Do not put things such as permanent liquid, cosmetic 
liquids, perfumes or mineral water into the supply 
tank. Doing so may lead to malfunctions or cause 
allergic skin reactions.

Do not use tap water.

Do not touch the Water Container 
Cap immediately after operation ceases.

The Water Container Cap will still be hot right after 
operation and touching it may lead to being burned.

Do not use with chemicals for cold 
temperature permanent waves.

Do not use with cold permanent wave chemicals. 
Their use may lead to allergic skin reactions.

Summary of Contents for Ak-200





















Reviews: