background image

21

wax

Compound

USER MAINTENANCE INSTRUCTION

Be sure to disconnect the power plug from the wall socket 
for maintenance and cleaning of the equipment.

The plastic, plated, or painted parts should be wiped 
with a dry and soft cloth.

Never use volatile chemicals such as thinner, alcohol, gasoline, and kerosene; detergents containing organic materials; 
acidic‑, alkaline‑ or chlorine‑based detergents; and wax containing abrasive compound, sponge, scrubber, etc.

Splashing of water on the control panel or metal parts may 
result in equipment failure or rusting. Immediately dry the 
equipment with a soft cloth.

When fixed contamination or oil adheres to the equipment, 
wipe it off with a cloth dampened with a water‑diluted 
neutral detergent.

Kerosene

Alcohol

Thinner

Chemicals

Soft cloth

The equipment should not be exposed to moisture and water.

Soft cloth

Soft cloth

Power plug

Neutral

Any other servicing should be performed by an authorized service representative.

C o n s u m a b l e   S u p p l i e s

□Power cord  □Caster

The consumable supplies imply parts that are subject to abrasion, deterioration, change in appearance, or breakage through 
use. If a part has been worn significantly or deteriorated, or if it is broken, the parts must be inspected or replaced. 
Immediately stop using the equipment, turn off the power switch, disconnect the power plug, and immediately contact the 
nearest dealer or our company directly.

Repair or replacement of parts shall be executed under the warranty or may incur a fee. 
(*The level and timing of wear, deterioration, or breakage differ according to the operation environment or conditions of the 
customer.) In addition, regarding the parts that can be replaced by the customer, it is not necessary for the customer to bear 
the basic charge and the technical fee, but the customer is requested to bear the shipping fee separately. For any questions 
regarding the replacement procedures, please contact the nearest dealer or our company directly.

●Consumable Parts (The following parts must be purchased since they are 

    excluded from the warranty.)

Summary of Contents for AK-S23S

























Reviews: