background image

2

Using the auto-return function (switch R on the foot control)

What is the auto-return function?

 

3

 

Cancel function

To stop midway the chair movement activated by a preset switch or the auto-return switch, step on any switch on the foot 
control. The cancel function will be activated, and the chair will come to a halt.

 Using the height-adjustable service tables

Height-adjustable

service tables

1

Pulling up the height-adjustable service tables to the desired levels

Service table
operation button

2

It automatically returns the seat height, the backrest angle, and legrest position to 
the initially set positions when you hold down the auto-return switch (R) on the foot 
control for at least 1 sec.
To prevent accidental operation, the auto-return switch is designed to react only 
when it is held down for at least 1 sec.

 When using the auto-return function, make sure that there is no person (or animal) near the 

  

support arm underneath the legrest and the footrest.

For hand or nail care, you can rest the customer’s arms on the height-adjustable service tables.
The service tables are adjustable for height to fit with the customer’s elbows.
Adjust the height to best support the elbows before providing care.

After raising and using the height-adjustable
service tables, be sure to return them to the initial
position. They have a load capacity of 10 kg. Do
not let the customer place his/her weight onto
his/her hands on the raised height-adjustable
service tables to raise him/her from the seat. The
height-adjustable service tables may break.
If nail polish, nail polish remover, or any other
chemical adheres to the upholstery of the height
adjustable service tables, wipe it off immediately.
Do not raise the height-adjustable service tables
too high. They may come off. Before use, rock
them back and forth to make sure that they are fixed.
When lowering the height-adjustable service
tables, be careful not to allow the operator’s or the
customer’s hand to become pinched.

- Pull up each of the height-adjustable service tables to the desired level at 

which you feel a click. Releasing the height-adjustable service table will lock 
it there.

- You can raise the height-adjustable service tables up to approximately 16 

cm higher than the seat top.

Lowering a height-adjustable service table: Be sure to keep 
supporting the height-adjustable service table with one hand while 
holding down the service table operation button to return the 
height-adjustable service table onto the chair body.

Lower the height-adjustable service table while holding down the 
service table operation button. Just pressing the button does not 
automatically lower the service table.

CAUTION

WARNING

15

Summary of Contents for ESTHE PLACE

























Reviews: