background image

Cleaning Instructions

 Cleaning precautions

Wipe them gently with a dry soft cloth.

Synthetic upholstery parts

If very dirty

 

Wipe them with a dry soft cloth.

Plastic parts

If very dirty

Wipe them with a dry soft cloth.

Control and metal parts

 

Wipe them with a dry soft cloth or a cloth soaked in water and

wrung thoroughly.

Height-adjustable service tables

NOTE

 Never use the following:
 Thinner, alcohol, petrol, paraffin or any other volatile chemicals, or wax or sponges containing
 abrasive. 

If you use the chair for the first time after a long period of non-use, clean it before use. After wiping it clean, be sure to
check that the chair operates properly and safely.

Clean the chair after use to keep it clean.
Before cleaning the chair, be sure to disconnect the power plug from the socket.

Wipe them with a cloth dampened with 
diluted neutral detergent.
Any clothing or belt colour stains on the 
upholstery should be wiped off as quickly 
as possible with a cloth dampened with 
diluted neutral detergent. Otherwise, the 
plasticiser can cause the stains to soak 
into the upholstery.

Dampen a cloth with neutral detergent 
diluted with water to approximately 
10%. Wring the cloth thoroughly, wipe 
the parts with it, and allow them to dry 
well.

Do not wipe them with a wet cloth. Water and dampness
affects these parts.
If you spill water on them, wipe off the moisture immediately.
Otherwise, rust or a fault in electric parts may result.

If you use a damp cloth, wipe off the

moisture well. Remaining moisture may

accelerate hydrolysis.

Acids and alkalis affect the parts. Do not

use thinner, petrol, nail polish remover, or

dusters impregnated with chemicals.

Any clothing or belt colour stains on the

upholstery should be wiped off as quickly

as possible with a cloth dampened with

diluted neutral detergent. Otherwise, the

plasticiser can cause the stains to soak

into the upholstery.

Thinner

Alcohol

Petrol

wax

Chemicals

Abrasive-

containing

 This product is an electrical device. Do not wash it with water. Failure or an electric shock may 

result.

 Before wiping the chair or cleaning it in any other way, turn off the power switch and disconnect
 the power plug. Otherwise, an electric shock or fire may result. Accidental operation of the chair
 during cleaning may cause injury.

 To clean the upholstered parts, do not use any detergents containing organic solvents.

 Any clothing or belt colour stains on the upholstery should be wiped off immediately with a cloth 

dampened with diluted neutral detergent to prevent them from soaking into the upholstery.

CAUTION

WARNING

Neutral

Neutral

Neutral

17

Summary of Contents for ESTHE PLACE

























Reviews: