background image

If any of the following problems occur, check for the following possible causes before asking for repair:

Problem

Check points

Recovery procedures

 The chair does not move.

Isn’t the power switch off?

Turn on the power switch 
(see page 8).

Has a fuse of the salon’s switchboard
or breaker been tripped?

Hasn’t the chair been kept operating
for a long time?

 

Overheating prevention device
This protective circuit stops the motor
to avoid abnormal overheating of
internal mechanisms due to
continuous operation.
For this reason, the chair may stop
operating temporarily.

 Using a built-in socket turns off the 

 power switch.

SNAP

Breaker
tripped?

Is the total amount of current used
less than the allowable value?

Hasn’t the device, plugged into 
abuilt-in socket, tripped the breaker?

The breaker function operates if the
current used exceeds the allowable
value. Use an amount of current that is
less than the allowable value, and turn
on the power again.

The following symptom is not a sign of fault.

 Strange noise at the time of start-up

Daily Inspection Instructions

Troubleshooting

Breakers

 For long and safe use of the chair, inspect it according to the “Daily Inspection Checklist” on page 21.

Follow the Daily Inspection Procedures to inspect this product on a daily basis. Continued use without 
daily inspection may cause failure or accidents.

Its overheating prevention device has
been activated. Leave the chair for
approximately 10 min.,
and it will return to the normal condition.

Replace the fuse or turn on the 
breaker.

Replace  the  plugged  device  by some
other device. If the power switch still
cannot be turned on, contact your
nearest dealer or Takara Belmont.

Breakers protect the chair from 
being damaged when the 
allowable current is exceeded.

 The noise is produced when the lubricating oil inside is cold, which does not 

 affect the chair’s functions. The noise will cease soon.

If the problem persists after you have checked the points and tried the remedy given above, turn off the power immediately,
disconnect the power plug, and contact your nearest dealer or Takara Belmont. 

No problem with 
the switchboard?

Power turned on?

Plug inserted?

Rating
exceeded?

18

Summary of Contents for ESTHE PLACE

























Reviews: