background image

 Do not allow anyone weighing 135 kg or 

  

more to sit in this chair.

 Always use your hand to operate the 

  

power switch.

 Before using this chair for work, make sure 

  

that all the parts work properly and safely.

 Be careful not to trip over the power cord.

 Stay alert for any looseness, wobbling, 

tilting, vibration, noise, heat or odour, 

and inspect the chair for any abnormalities.

 Immediately wipe off any spillage of 

  

chemical solutions or water.

 Be careful not to let children or other 

  

customers touch any switch.

 Before starting automatic operation, 

  

check the surroundings.

 

When cleaning the chair, never use povidone-

  

iodine (Isodine), sodium hypochlorite, or any 

  

other disinfectant highly corrosive to metals.

A fault in the chair may result.

 Do not place any objects on the power cord.

It may result in damage to the cover or malfunction.

 The headrest will be detached if it is raised too high.

operation lever.

 

Cautions concerning urethane upholstery

It may tip over or not operate properly.

If you feel something is wrong, however trivial it may seem, stop 
using the chair immediately, unplug it, and contact the dealer or 
Takara Belmont.

Keep an eye on customers (especially children), so that they do 
not operate this chair or accidentally set it into motion, causing 
accidents.

Before starting automatic operation of the chair, make sure that 
the customer is sitting in the correct spot. During the automatic 
operation, keep an eye on the customer.

If  chemical  solutions  cause  spots  or  spill  over  electric  parts, 
malfunction or electric leakage may result.
Any spillage must be wiped off quickly with a dry soft cloth such 
as towel.

Before  operating  the  chair,  pay  careful  attention  to  the 
surroundings and warn people there about the operation.

 When using the foot control, take extra 

  

care not to press different switches.

 

If the breaker (the power switch) trips frequently, 

   

contact the dealer or Takara Belmont.

 After using the chair, turn off the power 

  

switch.

It may result in damage to the cord and may cause disconnection 

 Do not hit or scratch the equipment hard.

 Stains with clothing dye

The synthetic upholstery of the chair may become stained with clothing dye when in contact with clothes or belts worn by customers. 
Any colour stains should be wiped off as quickly as possible with neutral detergent diluted with water to approximately 10%, so that 
the stains do not soak into the upholstery.

 Upholstery deterioration and colour transfer due to contact

- Contact with other plastic products, coated items, solvents and adhesive tape may take the shine off, crack, deform or peel the 

upholstery surface.

- Contact with newspaper or other printed matter may stain the upholstery.
- Contact with benzene, nail polish remover, or alcohol may cause plasticiser to leach from the upholstery or dissolve, take the shine 

off, harden, weaken or peel the upholstery surface.

- Contact with bleach or bleached bed sheets may take the shine off or discolour the upholstery surface.
- If placed near an iron, a heater or other source of excessive heat, the upholstery may deform or discolour.
- Avoid direct sunlight by using a curtain. Otherwise, the upholstery surface may shrink or change in other ways.
- Do not place any heavy objects on the chair. They may leave marks or long-lasting creases.

CAUTION

4

Summary of Contents for ESTHE PLACE

























Reviews: