background image

Safety Precautions (To be strictly observed)

CAUTION

Do not put hot water into the water‑supply bottle.

Handling of Power Cord

Do not touch the water‑supply cap when it is hot.

Do not put hot water into the water‑supply
bottle. When you do this, burns, machine
errors, or machine failure may result.

Do not touch the water‑supply cap during
operation or right after the operation.
Since the cap is hot, burns may result.

Never put liquids such as perm solution,
essence face lotion, aromatherapy oil, and
mineral water other than deionized water
into the water‑supply bottle or the
water‑supply bottle pan. Ignoring this
precaution may result in machine failure.

Do not put a heavy object on the main product unit.

Do not put an object exceeding 1 kg on the
machine. Ignoring this precaution may
result in burns or physical injuries
caused by falling, deformation, or
breakage of the machine.

Pay attention to interference with other
equipment and jamming.

When moving the machine or other equipment,
be careful about interference or jamming.
Ignoring this precaution may result in
falling or breakage of the machine or
physical injuries.

Do not operate the machine without installing
the flexible hose.

Operation of the machine without
installing the flexible hose will allow
the mist to be sprayed onto the machine,
which may result in electric shock hazard,
electric leakage,or short circuit.

Do not use chemical agents that are designated
for use in room temperature.

When disconnecting the power plug, do not
hold it at the cord, but pull it out while
holding the plug part at the end.

When discharging water, do not put your
hands, legs, etc., into the drain outlet.
Hot water may come out of the outlet,
which may cause burns or injuries.

If the power cord or the power plug is
damaged or when with the connection to
the wall outlet is loose, do not use the
cord or the plug.

Do not move the main unit by holding the
power cord. Do not damage, break,
forcibly bend, twist, pull, or bundle the
cord. Furthermore, putting a heavy object
on the cord, jamming of the cord into
objects, or modifying the cord will damage
the cord, resulting in fire or electric
shock hazard.

Be sure to use the power cord in the state
where it is affixed to the main unit with
the screws attached (see page 5). Ignoring
this precaution may result in fire or
electric shock hazard.

3

Never put liquids other than deionized water
into the water‑supply bottle pan.

Ignoring this precaution may result in
machine failure or physical injuries
caused by malfunction of the machine.

Do not flush the inside of the water‑supply
bottle pan with a flushing agent.

Do not use alkali color or cold 2‑bath
permanent‑waving agents. Ignoring this
precaution may cause skin infections,
such as a rash.

Do not put your hands and legs closer to the
drain outlet when discharging water.

Do not use parts and components other than the
designated options.

Ignoring this precaution may prevent
normal use and may cause burns or physical
injuries.

Summary of Contents for SPA MIST II AK-160

































Reviews: