22
Step 2 – Unlock and adjust the support leg
[MIDI_I-SIZE_027] Press the button on the height
adjustment mechanism as far in as possible, and slide
the support leg up or down. When the desired position
is reached, release the button and check that the
support leg is locked in place. This is indicated by a
click, and a green marking on the top of the button.
WARNING!
If the support leg is not set at the correct height, there
is a risk of serious injury to the child or other
passengers in the case of an accident.
[MIDI_I-SIZE_037] The correct position of the
support leg is set when the support leg of the TAKATA
Qq#J# <% %
@%</ % %;%
support leg is fully showing a green marking.
Step 3 – Fold in and lock the support leg
[MIDI_I-SIZE_025] To be able to fold in the support
/% %%-
ting. Push the release slider of the folding mechanism
to the side, and swing the support leg towards the
underside of the base. When the support leg lies snug
against the underside of the TAKATA I-SIZE BASE,
the support leg is locked into place by a spring in the
release slider.
Adjusting the ISOFIX connectors
The two ISOFIX connectors on the TAKATA I-SIZE
BASE must be adjusted, according to the position of
the ISOFIX points in the vehicle. Each of the
connectors can independently be set to one of six
different lengths, with the various settings indicated by
%%&
obtained when the connectors are at full extension,
'% ' &
Step 1 – Unlock the ISOFIX length adjuster
[MIDI_I-SIZE_028] Press the left-hand button on the
ISOFIX length adjuster as far in as possible and hold
it in position. The adjuster is positioned on the inner
side of the TAKATA I-SIZE BASE.
Step 2 – Adjust the ISOFIX connector
At the same time, pull the left-hand ISOFIX
connector, positioned on the outside of the TAKATA
I-SIZE BASE, into the required position.
Step 3 – Lock the ISOFIX length adjuster
Release the button and connector, and check whether
the latter is locked in place. This is indicated by a
click, and a green marking on the button.
NOTE!
The two ISOFIX connectors must be adjusted
independently. Repeat steps 1 to 3 for the right-hand
connector.
WARNING!
[MIDI_I-SIZE_029] When securing the TAKATA
I-SIZE BASE in the vehicle, ensure that both ISOFIX
connectors are set to the same position. To do this,
%% %%%
match up (or that both are blank). Failure to observe
this notice may seriously risk your child’s safety, and
the safety of other passengers, in the event of an
accident.
Step 4 – Unlock the ISOFIX connectors
[MIDI_I-SIZE_030] Unlock the left and right-hand
ISOFIX connectors, by taking hold of the release
sliders on each, moving the locking sliders of the
release sliders down and, at the same time, pulling the
release sliders towards the support leg. The connectors
have been correctly unlocked if you can see a red
marking on the top of each slider. If green markings
are shown, the connectors are still locked in place.
Releasing the rear connection hooks
[MIDI_I-SIZE_031] The TAKATA MIDI I-SIZE is
attached to the TAKATA I-SIZE BASE via connection
hooks at the front and rear. To free the TAKATA MIDI
I-SIZE from the TAKATA I-SIZE BASE, you need
only to release the rear hooks.
The rear hooks unlock together, so you only need to
push down one of the release elements on the exterior
of the connection arms. The connection hooks have
been correctly unlocked if you can see a red marking
on the top of each release element.
If green markings are shown, both, or in case of
partially green markings possibly only one of the
hooks are still locked in place. Please always also see
the warnings in Section 4 – Use in the vehicle
(Securing the TAKATA MIDI I-SIZE in a backward-
facing or forward-facing position).
4. USE IN THE VEHICLE
WARNING!
[MIDI_I-SIZE_009] Never use the TAKATA I-SIZE
BASE on its own, or without properly securing the
