25
de
it
nl
fr
es
en
arrows on the outside of the seat and on the rear
connection arms of the TAKATA I-SIZE BASE. The
bolts are properly locked into the rear connection
hooks when each one clicks into place, and you can
see a green marking on the top of each hook’s release
element.
[MIDI_I-SIZE_046] To secure the connection rod in
the foot area of the TAKATA MIDI I-SIZE with the
front connection hooks of the TAKATA I-SIZE BASE,
press down from above on the seat section of the
TAKATA MIDI I-SIZE, until you hear a click.
WARNING!
[MIDI_I-SIZE_040] Do not use the TAKATA MIDI
I-SIZE if it is not correctly secured to the TAKATA
I-SIZE BASE. It is properly locked in place when you
can see a green marking on the top of each rear hook’s
release element and if you checked prior to installation
of the TAKATA MIDI I-SIZE on the TAKATA I-SIZE
BASE that the rear connection hooks were open.
NOTE!
[MIDI_I-SIZE_043] Check the TAKATA MIDI
I-SIZE is correctly secured to the TAKATA I-SIZE
BASE, by gently shaking the seat in each direction. If
the seat is not properly secured to the base, repeat Step
2 – Lock the seat into the TAKATA I-SIZE BASE
until it is in the correct position.
Removing the TAKATA MIDI I-SIZE from the
TAKATA I-SIZE BASE
Step 1 – Release the rear connection hooks
[MIDI_I-SIZE_031] The rear hooks unlock together,
so you only need to push down one of the release
elements on the TAKATA I-SIZE BASE rear
connection arms. At the same time, tilt the TAKATA
MIDI I-SIZE forward (in the direction of travel), so
that the connection bolts of the seat come out of the
rear connection hooks of the base.
Step 2 – Free the seat from the front connection hooks
and remove
[MIDI_I-SIZE_047] Free the connection rod of the
TAKATA MIDI I-SIZE from the front hooks of the
TAKATA I-SIZE BASE by sliding the TAKATA MIDI
I-SIZE backward, against the direction of travel. You
should now be able to lift the TAKATA MIDI I-SIZE
from the TAKATA I-SIZE BASE, and remove it from
your vehicle.
Removing the TAKATA I-SIZE BASE
Step 1 – Unlock the ISOFIX connectors
[MIDI_I-SIZE_030] Separate the connectors on the
TAKATA I-SIZE BASE from the ISOFIX points in the
vehicle, by moving the locking sliders of the release
sliders down and, at the same time, pulling the release
slider on each connector forward (in the direction of
travel). The components have been separated if a red
marking can be seen on the top of each connector.
Step 2 – Retract the ISOFIX connectors
[MIDI_I-SIZE_028] Press the left-hand button on the
ISOFIX length adjuster as far in as possible. The
button is positioned on the inner side of the TAKATA
I-SIZE BASE. At the same time, push the left-hand
connector back into the TAKATA I-SIZE BASE.
The two ISOFIX connectors must be adjusted
independently. Repeat Step 2 for the right-hand
connector.
NOTE!
The connectors have been fully retracted when all
%%
ISOFIX connectors.
Step 3 – Fold in the support leg and remove it
[MIDI_I-SI MIDI_I-SIZE_026] Fold the
support leg in, as described in Section 3 – Basic
instructions (Adjusting the support leg). You should
now be able to remove the TAKATA I-SIZE BASE
from your vehicle.
5. SECURING YOUR CHILD
NOTE!
For safety reasons, children should always get in and
out from the passenger side of the vehicle, or directly
onto a sidewalk.
Step 1 – Adjust and fasten the inner padding and
straps
[MIDI_I-SI MIDI_I-SIZE_022] Before
sitting your child in the TAKATA MIDI I-SIZE,
loosen and open the straps, as described in Section 3
– Basic instructions (Loosening the straps and opening
the buckle), and move them out of the way.
[MIDI_I-SI MIDI_I-SIZE_007] Once your
child is sat in the TAKATA MIDI I-SIZE, place the
shoulder straps over the shoulders and the lap belt
over your child’s lap, taking care not to twist or tangle
