background image

SAFETY

CAUTIONS WHEN WORKING

1

1

CAUTIONS WHEN WORKING

1C0BF00

CAUTIONS WHEN WORKING

When disassembling or assembling

• Clean the machine before disassembly.
• Check the following items and record the results:

a. Model, machine serial number, hour meter.
b. Reason for repair, repair history.
c. Are the filters dirty?
d. The conditions of the fuel and oil.
e. Any damage or looseness to any part?

• Where necessary, draw alignment indicators to avoid

assembly errors. To avoid misconnection, place indi-
cators such as reference tags on pipes.

• Clean all disassembled parts and new parts, arrange

them neatly, and place indicators as necessary.

• Be sure to replace all seals and cotter pins with new

ones.

• Keep those parts that should not come in contact with

water or oil away from those with oil on the surface.

• When installing bearings, bushings and oil seals, a

press tool should be used. If a hammer is used, use a
cushioning material to avoid damage.

• Wipe all joining surfaces clean until there is no dirt or

dust adhering to them.

• Wrap the thread tight with seal tape starting 1 or 2

threads away from the thread end. The tape should be
overlapped by about 10 mm (0.39 in).

When removing/installing the hydraulic unit

• Make sure that the temperature of the hydraulic oil has

dropped and is cool enough to work with.

• To prevent the hydraulic oil from escaping under pres-

sure, release the residual pressure in the piping.

• Be sure to install caps or plugs on all openings in the

hydraulic unit to prevent dirt from getting into the unit
through them.

• The hydraulic oil adhering to the unit is often mistaken

for an oil leak, so wipe off the unit thoroughly.

• Be sure that no damage is caused to the plating on the

rod in the hydraulic cylinder.

• Removal and installation of the hydraulic cylinder

should be done with the rod fully retracted.

• Be sure to bleed the air after installing the hydraulic

cylinder. (

 “4. Disassembly and assembly: Cylin-

der”)

• Always bleed the air when hydraulic oil is changed or

a hydraulic device is replaced. (

 “4. Disassembly

and assembly: Drive system”)

Summary of Contents for TB210R





















Reviews: