background image

DG-U100

18

7.2 Camera Tracking Settings

After the CU and the camera are connected, output the camera video to a monitor, use a remote 

to enter the camera settings, configure Camera ID and Baud. You can also view the Camera 

Protocol in the settings. Set the Baud value to 9600, and ID to desired (supporting up to 7 cameras, 

optional ID 1~7), and leave other parameters unchanged.

Once the camera parameters are set, rotate the CU CURSOR to enter camera tracking interface, 

as shown below:

Move the cursor to the checkbox beside the camera icon, and press the CURSOR knob to check 

tracking function. Then based on the configuration, check the corresponding camera ID, and modify 

its respective Camera Protocol (by moving the cursor to the protocol, and press the knob to switch 

protocol). Check  Flip  to flip around the camera footage if necessary.

Next, proceed to binding and positioning the camera:

Adjust the camera angle based on your capturing footage on the monitor (via camera remote), rotate 

the CU knob to move the cursor to below framed area:

Mode:FIFO

Gamera Tracking:

Flip

Sony Visca

Flip

Pelco-P

Flip

Sony Visca

Flip

Sony Visca

Flip

Sony Visca

Flip

Sony Visca

Flip

Sony Visca

Language

1:
2:
3:
4:
5:
6:
7:

SYN

Vol 31

:

Cha

.

irman11

6 41 .0 0M H z

11

A

TxGa.in:06

1

Wireless Conference Microphone System

Summary of Contents for DG-U100

























Reviews: