background image

11

① 

Power indicator: when the mic is connected to relevant device and 

running, the LED illuminates blue; when XLR cable is disconnected, the 

LED light will be off.

② XLR interface: connect with audio device (e.g., audio interface, mixer, 

power amp) via XLR cable.

Function Descriptions

1. Install the mic clamp clockwise onto the mic stand or boom arm.

2. The front side of the mic is the side with silkscreened “PC-K200” and 

blue LED indicator. Face the front side towards the sound source. Install the 

mic onto the mic clamp, adjust to a proper angle, and tighten the clamp 

screw until fully secured. It is recommended to keep the installed mic tilted 

upwards to prevent accidental mic drop and damage in case of loose mic 

clamping, as shown:

3. Install the included foam windscreen onto the mic.

Operation Instructions

① 

Note: The foam windscreen can filter out plosives and protect microphone capsule 

from moisture such as speech droplets, but it may affect audio transparency slightly 

and therefore should be used at your preference.

Professional  Recording  Microphone

PC

-

K200

Summary of Contents for PC-K200





















Reviews: