background image

WARNING! Danger of injury due to broken glass! Risk of injury due to falling modules!  

The modules are primarily made of glass and must therefore be handled with appropriate caution. 

·  In order to ensure safe mounting, familiarize yourself with all applicable national regulations for work safety and 

accident prevention.

·  Wear suitable protective clothing (e.g. safety shoes, protective gloves) in order to prevent injuries.
·  If the front glass is broken, or the back sheet is torn, contact with any module surface or the frame can cause 

electric shock.

2.2  PRODUCT PRECAUTION

·  Do not attempt to disassemble the modules.
·  Do not remove any attached nameplates or components from the modules.
·  Do not open the junction box under any circumstances. 
·  Only carry out modifications to the modules that have  

been confirmed by Talesun in writing in advance. 

·  Do not carry out any extra drilling (e.g. for fasteners) on the modules. 
·  Use only insulated tools that are approved for work on electrical installations. 
·  Do not use light concentrators (e.g. mirrors or lenses) to attempt to increase the  

capacity of the module. The module may be damaged. This also voids the warranty.

2.3  TRANSPORT AND STORAGE SAFETY GUIDELINES

Inappropriate transport and installation may break the module.  
To prevent damage of the modules:
·  Transport the modules in their original packaging until installation. 
·  Store the modules securely in cool and dry rooms.  

The packaging is not weather-resistant!

·  Protect the modules against scratches and other damage,  

especially from impact at the edges or improper storage.

·  Ensure modules do not bow under their own weight.
·  Do not rest a module unprotected on its edges. This can damage the module and the frame.
·  Do not lift or move the modules using the cables or at the junction box under any circumstances! 
·  Do not set the modules down hard on any surface.
·  Do not subject the module surfaces to mechanical stress. 
·  Do not stand on the modules. 
·  Do not drop or place objects on the modules. 

Summary of Contents for TP672M-315

















Reviews: