background image

module type

Cell type

Cell 

Q’ty

Dimensions (mm)

A*B

J

K

M

N

O*

P*

TP672 Series

6inch crystalline (M/P) 6*12

1960*990

50

600

12

20

0.5~2 2.5~3

TP660 Series

6inch crystalline (M/P) 6*10

1640*990

50

425

12

20

0.5~2 2.5~3

TP654 Series

6inch crystalline (M/P)

6*9

1482*990

50

380

12

20

0.5~2 2.5~3

TP636 Series

6inch crystalline (P)

4*9

1482*672

50

380

12

20

0.5~2 2.5~3

TP596 Series

5inch crystalline (M)

8*12

1580*1064

50

416

12

20

0.5~2 2.5~3

TP572 Series

5inch crystalline (M)

6*12

1580*808

50

416

12

20

0.5~2 2.5~3

TP536 Series

5inch crystalline (M)

4*9

1199*551

50

320

12

20

0.5~2 2.5~3

Table 1:  Mechanical dimensions when modules installed at portrait orientation with Clamp fitting method
*Notes:  “672”  represents 72pcs 6inch cell, etc.
 

Dimension “O” represents the distance between clamp and frame.  /  Dimension “P” represents the thickness of clamp.

·  Use four clamps on the short frame, and the clamping zone is from module edge to 1/4 width of the short frame. 
·  Use a torque wrench for installation, and the compression for each clamps is not strong to avoid potential 

damages to module frames. The recommended maximum compression for each clamp is 20MPa (2900PSI). 

·  The module mounting structure must be made of durable, corrosion-resistantand UV-resistant material. All 

mounting hardware (bolt/flat washer/split washer/nut) should be stainless steel M8 size. 

·  The minimum recommended length for each clamp is 50mm. 
·  The modules have been designed to resist a static load of 2400Pa, and the resistance value can decrease if 

modules are not mounted following the instruction above. 

METHOD C: INSERT MOUNTING

Fringe side installation

Middle modules installation

The movement of the mount-
ing rail and the clamps center 
line are recommended to be 
within the black arrow area.

WATER RUNOFF

·  Ensure that the drainage openings of the frame are left open following installation to allow water runoff. This 

prevents frost damage. Install the module in such a way that rainwater and snowmelt can run off freely to avoid 
standing water or pudding.

Summary of Contents for TP672M-315

















Reviews: