background image

                      

 

 

TALEX Sp. Z O.O. Sp.K. 

ul. Dworcowa 9C  

77-141 Borzytuchom  

tel. (59) 821 13 26.  

English mob.: +48 507 828 310 

e-mail. 

biuro@talex-sj.pl

 

www.talex-sj.pl

  

 

 

                 

User Manual 

              FastCUT 300 Disc Mower

 

 
 

Page 

8

 of 

56

 

 

 

 

3. Rules of safe operation 

3.1 User safety 

The disc mower can only be used by adults, who have learnt how to operate it and have read 

this Instruction Manual, as well as have appropriate qualifications. Mowers should be handled 

with all safety precautions, and in particular: 

 

Apart from this Instruction Manual, observe also general rules of health and safety at 

work. 

 

Observe warning symbols placed on the machine.  

 

It is strictly forbidden, to operate the machine by persons under the influence of alcohol 

or other intoxicants. 

 

Never allow, that the vehicle servicing the mower should be driven by a person other 

than the mower operator, and under no circumstances allow any other persons to be on 

the vehicle, or on the machine, during its operation. 

 

The mower may be operated by a person who holds a proper driving licence for the 

vehicle equipped with the mower, in accordance with the manufacturer's instructions.  

 

The operator’s work station while working with the mower is the cab of the vehicle 

equipped with the machine. 

 

Please note, that there are many parts of the mower that may cause an injury (sharp 

edges, protruding parts, etc.). During the use of the equipment, exercise particular 

caution when moving close to the above-mentioned critical spots, and obligatorily use 

the following personal protection equipment: 

  

- protective clothing, 

 

- protective gloves, 

 

- protective footwear 

 

It is forbidden to carry persons or objects on the machine.  

 

Persons who have not read the Instruction Manual are not allowed to operate the 

machine. 

 

The mower operator must be provided with the first aid kit complete with instructions 

of use. 

 

When driving a vehicle with the mounted, but not working, mower, ensure the safe 

transport height of ~ 0,5m above the ground. 

 

Before driving, switch the mower to the transport setting and use the front three-point 

hitch to raise it. For parking, the machine must be lowered. 

 

For transport, the mower must be set to the transport position and raised by means of 

the tractor's three-point hitch. 

 

Take special care when driving on public roads, and comply with the applicable road 

traffic regulations. 

Summary of Contents for FastCUT 300

























































Reviews: