1 - 65
Chapter 3 Removal and Replacement Procedures (RRPs)
RRP4.6
CLUTCH ASSEMBLY PH (PL 4.1.21), CLUTCH REGI (PL 4.1)
Removal
1)
Remove the COVER REAR 500 (PL 7.1) (RRP7.9).
2)
Remove the FUSER ASSEMBLY (PL 6.1) (RRP6.8).
3)
Remove the COVER REAR (PL 1.1) (RRP1.1).
4)
Remove the CHUTE TRANSFER (PL 6.1) together with the BTR ASSEMBLY (RRP6.9).
5)
Remove the 150 FEEDER ASSEMBLY (PL 4.1) (RRP4.1).
6)
Disconnect the connector (P/J242) of the CLUTCH ASSEMBLY PH from the HARNESS ASSEM-
BLY TRAY 1 (PL 4.1) (Figure 1).
7)
Remove the E-ring securing the CLUTCH ASSEMBLY PH, and remove the CLUTCH ASSEMBLY
PH from the SHAFT FEED (PL 4.1) (Figure 1).
8)
Disconnect the connector (P/J243) of the CLUTCH REGI from the HARNESS ASSEMBLY TRAY
1.
9)
Remove the E-ring securing the CLUTCH REGI, and remove the CLUTCH REGI from the ROLL
REGI METAL (PL 4.1).
Figure 1. Registration & PH Clutches
Replacement
The part names differ with the CLUTCH ASSEMBLY PH and CLUTCH REGI, but they are
the same parts.
1)
Install the CLUTCH REGI to the ROLL REGI METAL (PL 4.1), and secure it using the E-ring.
When installing, make sure that the notch of the CLUTCH REGI is combined with the
boss of the CHUTE REGI.
2)
Connect the connector (P/J243) of the CLUTCH REGI (PL 4.1) to the HARNESS ASSEMBLY
TRAY 1 (PL 4.1).
3)
Install the CLUTCH ASSEMBLY PH to the SAHFT FEED, and secure it using the E-ring.
Summary of Contents for 9045N
