8 - 15
Chapter 8 Printer Specifications
5. Environmental Specifications
5.1 Installation and Storage Requirements
5.1.1 Print Engine Installation Requirements: Unpacked condition, an EP Cartridge installed.
5.2 Acoustic Noise
Sound power shall be determined in accordance with ISO 7779 annex C (9 Positions Method, logarithm
mean value).
*Standby mode:
5.00 B
*Low power mode:
5.00 B
*Sleep mode:
Only background noise (FAN OFF)
*Printing mode:
5.3 Inclination
Errors shall not occur when the print engine is operated within an inclination of +/- 5
o
.
5.4 Illumination
Errors including manor print quality errors, shall not occur below 3,000 Lux (without direct sunlight)
5.5 Dust Emission
The print engine shall not emit more than 4.0 mg/h.
Method: BAM RAL-UZ (Edition October 2003)
5.6 Chemical Substances
The print engine, including a photoreceptor and toner, shall not contain nor use for fabrication any ozone
depleting chemicals or any PCB, PBDE, Trichloroethylene and Asbestos.
:
1. PCB: Polychlorinated Biphenyl
2. PBDE: Polybrominated Diphenyl Ether
3. CFC: Chlorofluoro Carbons
4. PBBO: Polybrominated Biphenyl Oxides
5. PBB: Polybrominated Biphenyl
Condition
Temperature (
o
C) Humidity (% RH)
Altitude (m)
Remarks
Operating
5 - 35
15 - 85
0 - 3,500
non-condensing
Non-operating
-20 - 40
5 - 85
Configuration
Specification LWA (B)
Base Engine
6.95 B
Base Engine with
options
(See Note 1)
7.50 B
Summary of Contents for 9045N
