background image

English

WIB-5

Page 16

Dangerous environments

A working area that is too small or cramped is unsuitable and can cause
accidents, fires and injury. Prevent this by working in a clean, dry room

with enough freedom of movement.

Other dangers

Children can cause any of the accidents mentioned above because they
are inattentive and not responsible enough. Children under the age of

14 should not be allowed to work with this module.
Little children can swallow small components with sharp edges, with

fatal results! Do not allow components to reach small children.
In schools, training centres, clubs and workshops, assembly must be

supervised by qualified personnel.
In industrial institutions, health and safety regulations applying to

electronic work must be adhered to.

EMC declaration

This product is developed in accordance with the European standards
EN 55014 and EN 50082-1, tested corresponding to the EC - directive
89/336/EWG (EMVG of 09/11/1992, electromagnetic tolerance) and

meets legal requirements.
To guarantee the electromagnetic tolerance you must take the

following precautions:

§

 

Connect the transformer only to an approved mains socket installed
by an authorised electrician.

§

 

Make no changes to the original parts and accurately follow the
instructions, circuit diagram and connections diagrams included
with this manual.

§

 

Use only original spare parts if you have to repair module.

Summary of Contents for WIB-5


















Reviews: