background image

50

TANDBERG Gateway

Configure the Gateway

File Management

The File Management allows viewing or changing of pictures and sounds shown to the caller when connecting to
the gateway.

To view/hear the currently installed files, press the name of the ‘File’ on the left side of the window. The file will
then be shown/played. At the bottom of the page, custom file requirements are listed for each of the file-types.

The following can be specified:

• 

Encryption Required Picture

• 

Gateway Call Proceeding Picture

• 

Gateway Extension Enquire Screen Picture

• 

Downspeeding In Progress Picture

• 

Gateway Call Welcome Sound

• 

Gateway Extension Enquire Sound

• 

System Parameters

• 

Directory

To add a new file, press ‘Browse...’ to find the file, and then press ‘Upload’.

For each of the customized files, a ‘Delete’ button will be added in the ‘Type’ column. By pressing ‘Delete’, the
default file will replace the custom file.

Pressing ‘System Parameters’ allow you to do backup and restore the settings on the gateway.

Pressing ’Directory’ allow you to upload a Phone Book to the gateway. The Phone Book is used for the Call
Transfer function.

P

LEASE

 

REFER

 

TO

 

THE

‘L

EGAL

 F

ILE

 T

YPES

FIELD

 

AT

 

THE

 

BOTTOM

 

OF

THE

 

PAGE

 

FOR

INFORMATION

 

ABOUT

LEGAL

 

FILE

 

FORMATS

.

NOTE

Summary of Contents for D13187-03
































































Reviews: