background image

082406-40 TC36.CSTE 

5056.42801.C

WARNING:  If the information in this 
manual is not followed exactly, a fi re or 
explosion may result causing property 
damage, personal injury or loss of life.

-- Do not store or use gasoline or other 
fl ammable vapors and liquids in the vicinity 
of this or any other appliance.

-- WHAT TO DO IF YOU SMELL GAS

•  Do not try to light any appliance.
•  Do not touch any electrical switch; do 

not use any phone in your building.

• Immediately call your gas supplier 

from a neighbour’s phone.  Follow 
the gas supplier’s instructions.

•  If you cannot reach your gas supplier, 

call the fi re department.

--Installation  and service must be 
performed by a qualifi ed installer, service 
agency or the gas supplier.

FOR YOUR SAFETY

IMPORTANT:

THESE INSTRUCTIONS ARE TO 

REMAIN WITH THE

HOMEOWNER

INSTALLATION

AND OPERATING 

INSTRUCTIONS

MODEL TC36ST

SERIES C

MODULAR

DIRECT VENT

SEE-THRU FIREPLACE

This appliance may be installed in 
an aftermarket permanently located, 
manufactured home (USA only) or mobile 
home, where not prohibited by local codes.

This appliance is only for use with the 
type of gas indicated on the rating plate. 
This appliance is not convertible for use 
with other gases, unless a certifi ed kit is 
used.

Summary of Contents for TC36ST









































Reviews: